JTEKT Corporation
Torrington THRUST NEEDLE BEARINGS TOR AXK-3552
Thrust needle roller and cage assemblies are complements of small diameter needle rollers, arranged in a spoke-like configuration. Needle rollers are equally spaced by means of a cage, its web section separates the rollers and provides guidance to keep them tracking in an orbital path. The purpose of these assemblies is to transmit a thrust load between two relatively rotating objects while greatly reducing friction. Thrust needle roller and cage assemblies also can be unitized with lipped washers to serve as raceway surfaces for the needle rollers. Washers can be supplied separately or can be mechanically unitized to the thrust needle roller and cage assemblies for ease of handling.
Torrington THRUST NEEDLE BEARING WASHERS TOR TRD-2435
Koyo TRD-2435 Thrust Washer, 38.1 mm ID x 55.55 mm OD, 3.2 mm W
Torrington THRUST BEARING WASHERS TOR TRC-2435
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRC-2233
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRB-2435
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRA-1828
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington THRUST BEARING WASHERS TOR TRA-1018
Ideally, a thrust washer should be stationary with respect to and piloted by its supporting or backing member whether or not this is an integral part of the shaft or housing. There should be no rubbing action between the thrust washer and any other machine member. The economics of design, however, often preclude these ideal conditions and thrust washers must be employed in another manner. In such cases, design details should be determined in consultation with your representative.
Torrington NEEDLE BEARINGS TOR JTT-1012
Koyo JTT-1012 Inch Series Caged Open Ends Drawn Cup Needle Roller Bearing, 5/8 in Dia Bore, 13/16 in OD, 3/4 in W, 1980 lbf Dynamic/2910 lbf Static Load
Torrington NEEDLE BEARINGS TOR JT-129
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway to the rollers. The small cross-section of the drawn cup bearing provides high load-carrying capability with minimum required space, drawn cup bearings are easily installed with a press fit in the housing.
Torrington NEEDLE BEARING INNER RACES TOR IR-88
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington NEEDLE BEARING INNER RACES TOR IR-242820
Koyo IR-242820 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1-1/4 in OAW, For Use With HJ-283720 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-2424
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington NEEDLE BEARING INNER RACES TOR IR-2020
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington NEEDLE BEARING INNER RACES TOR IR-192420
Koyo IR-192420 Inch Series Inner Ring, 1-3/16 in ID x 1-1/2 in OD, 1-1/4 in OAW, For Use With HJ-243320 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-101412
Koyo IR-101412 Inch Series Inner Ring, 5/8 in ID x 7/8 in OD, 3/4 in OAW, For Use With HJ-142212 Heavy Duty Needle Roller Bearing, Steel
Torrington NEEDLE BEARING INNER RACES TOR IR-081212
Koyo IR-081212 Inch Series Inner Ring, 1/2 in ID x 3/4 in OD, 3/4 in OAW, For Use With HJ-122012 Heavy Duty Needle Roller Bearing, Steel
Torrington NEDDLE BEARING INNER RACES TOR IR-1212
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Torrington FLAT THRUST NEEDLE BEARINGS NTA-4458
Thrust Needle Roller and Cage Assemblies are the complements of small diameter needle rollers, arranged in spoke-like configuration. Needle rollers are equally spaced means of cage, its web section separates the rollers and provides guidance to keep them tracking in an orbital path. The purpose of these assemblies is to transmit a thrust load between two relatively rotating objects while greatly reducing friction. Thrust Needle Roller and Cage Assemblies also can be utilized with lipped washer to serve as raceway surface for the needle rollers. Washers can be supplied separately or can be mechanically unitized to the Thrust Needle Roller and Cage Assemblies for ease of handling.
Torrington DRAWN CUP CLUTCH NEEDLE BEARINGS TOR RCB-162117
Drawn Cup Needle Roller Clutches are similar to drawn cup needle roller bearings in design, however, they allow free rotation in only one direction while transmitting torque in the opposite direction. These designs use the same small radial section as drawn cup needle roller bearings and are offered as clutch-only units or as clutch and bearing assemblies.
Torrington DRAWN CUP CLUTCH NEEDLE BEARINGS TOR RC-162110-FS
Drawn cup needle roller clutches are similar to drawn cup needle roller bearings in design, however, they allow free rotation in only one direction while transmitting torque in the opposite direction. These designs use the same small radial section as drawn cup needle roller bearings and are offered as clutch-only units or as clutch and bearing assemblies.
Torrington 9/16"-ID NEEDLE BEARINGS TOR B-97
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearings are easily installed with a press fit in the housing.
Torrington 9/16"-ID NEEDLE BEARINGS TOR B-912
Drawn Cup Needle Roller Bearings supports radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearing are easily installed with a press fit in the housing.
Torrington 7/8"-ID NEEDLE BEARINGS TOR BH-1416
Drawn Cup Needle Roller Bearings supports radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearing are easily installed with a press fit in the housing.
Torrington 7/8"-ID NEEDLE BEARINGS TOR B-1416-OH
Drawn cup needle roller bearings support radial loads and reduce friction between rotating components, with a drawn outer shell serving as a raceway for the rollers. The small cross section of the drawn cup bearing provides high load-carrying capability with minimum required space. Drawn cup bearings are easily installed with a press fit in the housing.
Recently Viewed
EATON 10250H5200 2-Element Heavy Duty Control Station, NEMA 1 NEMA Rating
Eaton's 10250T line of 30.5 mm pushbuttons features a heavy-duty zinc die cast construction. Reliability nibs improve contact reliability even under dry circuit and fine dust conditions. In addition, drainage holes prevent the buildup of liquid inside the operator, which can prevent operation in freezing environments.
3/32" -IDX7/32" -OD O-RINGS
1/2" X 24 60-GRIT SANDING BELT-ARC714091 >
.010" S/S PIANO WIRE-RL/1 LB.-PRC29010>
ITM 212CO0864 Heavy Duty Drill Bit, 1/8 in Drill - Fraction, 0.1250 Drill - Decimal Inch, 135 deg Point Angle, M35 Cobalt
3/16" HEX HAND HELD NUTDRIVERS-ARS66806>
