Koyo IR-2424 Inch Series Regular Width Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1.515 in OAW, For Use With Inch Series Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
-
BrandKoyo
-
UPC605790216763
-
Manufacturer Part NumberIR-2424
-
CountryUSA
-
FinishPolished Chrome
-
MaterialSteel
-
TypeRegular Width
-
SeriesIR Inch Series
-
Inside Diameter1-1/2 in
-
Outside Diameter1-3/4 in
-
Overall Width1.515 in
-
Suitable For Use WithInch Series Drawn Cup Needle Roller Bearing
- Ideal choice when shaft is not practical to use as inner raceway
- Designed to meet established inch tolerances
- Designed to be wider than matching drawn cup bearing
- Maximum shaft fillet radius cannot exceed inner ring bore chamfer
- Designed to provide a loose transition fit on the shaft and should be axially clamped against a shoulder
- If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD must not exceed the raceway diameter for the matching drawn cup bearing after being mounted on the shaft
- After mounting, if OD of inner ring exceeds the required raceway diameter for matching bearing, ring should be ground to proper diameter while mounted to shaft
-
Alternative Part NumberIR2424PBL125
-
UNSPSC31171547
-
Catalog
Recently Viewed
Koyo IR-2424 Inch Series Regular Width Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 1.515 in OAW, For Use With Inch Series Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
Browning 3-7/16"-ID 4-BOLT TRB PILLOW BLOCK BRW PBE-920F X 3-7/16
Browning® E920 series mounted tapered roller bearings feature durable 1-piece non-expansion housings with Type E mounting dimensions and limited misalignment. The E920 series contains setscrew locking collars for easy installation. It also contains a contact face riding seal in order to provide a good balance between contaminant entry, grease retention and friction. Depending on your application requirements, these bearings are available in a wide variety of bore sizes and housing configurations.
Gates® Power Transmission Polyflex® 5M560 Light Duty V-Belt, 5M Section, 3/16 in W Top, 22.05 in L Outside, 1/8 in THK, High Modulus Polyurethane
Developed by Gates and produced to patented manufacturing processes, these belts provide more load-carrying capacity at higher speeds to small multiple V-belt precision drives. This results in significant cost savings and improved design freedom.
NORMAL DUTY 1-15/16" -ID CAST IRON WIDE SLOT TAKE-UP BEARING-BRWVTWS231 >
Dremel® 414 Polishing Wheel, 1/2 in Dia
Jones Stephens™ D40140 No Caulk Shower Stall Drain With Stainless Steel Strainer, 2 in, 4-1/4 in Stainless Steel Grid, Brass Drain
Jones Stephens™ D40140 No Caulk Shower Stall Drain With Stainless Steel Strainer, 2 in, 4-1/4 in Stainless Steel Grid, Brass Drain
