POWERS 3/4" X 12" ZINC CONCRETE ANCHORS PWR 7451
The Power-Stud anchor is a fully threaded, torque-controlled, wedge expansion anchor. It is available in threaded, rod hanger and tie-wire versions suitable for applications in solid concrete and grout filled concrete masonry. The carbon steel threaded version is suitable for a variety of applications. The drill bit diameter necessary for proper installation is the same as the anchor diameter.
-
BrandDeWALT®
-
UPC075352781303
-
Manufacturer Part Number7451SD1
-
CountryUSA
-
FinishZinc Plated
-
Tensile Strength7860 lb
-
Thread Length9-1/2 in
-
MaterialCarbon Steel
-
Thread Size3/4-10
-
Thread TypeUNC
-
Maximum Work Thickness7-7/8 in
-
Minimum Embedment Depth3-3/8 in
-
Shear Strength12685 lb
-
Diameter3/4 in
-
Drill Size3/4 in
-
Overall Length12 in
-
TypeExpansion
-
Head TypeHex
- Consistent performance in high and low strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Anchor design allows for follow-up expansion after setting under tensile loading
- Length ID code and identifying marking stamped on head of each anchor
- Anchor design allows for follow-up expansion after setting under tensile loading ultimate pullout 5440 lb
- Normal weight concrete, structural sand-light weight concrete, concrete over steel deck and grouted concrete masonry are applicable materials
| Competitor Name | Cross-Reference Number |
|---|---|
| Fastenal | 2140548 |
-
UNSPSC31162102
-
Package DescriptionEACH
-
Standards/ApprovalsICC-ES AC01, ESR-2818/2966|UL Listed
-
Catalog
Recently Viewed
The Power-Stud anchor is a fully threaded, torque-controlled, wedge expansion anchor. It is available in threaded, rod hanger and tie-wire versions suitable for applications in solid concrete and grout filled concrete masonry. The carbon steel threaded version is suitable for a variety of applications. The drill bit diameter necessary for proper installation is the same as the anchor diameter.
Dodge® 023021 307 Type E-Xtra Pillow Block Roller Bearing Unit, 3-7/16 in Dia Bore, 10.81 to 11.19 in L Bolt Center-to-Center, 3-3/4 in Base to Bore Centerline, 14 in OAL 7-1/2 in OAH
Dodge® 023021 307 Type E-Xtra Pillow Block Roller Bearing Unit, 3-7/16 in Dia Bore, 10.81 to 11.19 in L Bolt Center-to-Center, 3-3/4 in Base to Bore Centerline, 14 in OAL x 7-1/2 in OAH
Electrical Outlet Strips
Dodge® 041860 Type USAF Pillow Block Roller Bearing Unit, 2-7/16 in Dia Bore, 8.63 to 9.63 in L Bolt Center-to-Center, 11.13 in OAL x 6.44 in OAH
Dodge® 041860 Type USAF Pillow Block Roller Bearing Unit, 2-7/16 in Dia Bore, 8.63 to 9.63 in L Bolt Center-to-Center, 11.13 in OAL x 6.44 in OAH
ASP-125-2-SSS Industry Standard Clamping Collar, 2-Piece Construction, 1-1/4 in ID x 2-1/16 in OD x 1/2 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. The BMU bearings are commonly referred to as thrust bearings. These bearings have a 40 deg contact angle to accept heavy axial loads. The bearings have Universally Flush Ground rings to facilitate mounting in multiple bearing sets. The inner and outer rings have identical widths. These bearings can be mounted as DB, DF and DT pairs or can be combined into triplex and quadraplex sets. When two bearings are mounted together, a clearance or preload may be obtained without the use of shims or spacers. This bearing has a machined brass cage and is not available with seals or shields. These bearings are most commonly used in vertical pump and motor applications.
