ASP-125-2-SSS Industry Standard Clamping Collar, 2-Piece Construction, 1-1/4 in ID x 2-1/16 in OD x 1/2 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630884
-
Manufacturer Part NumberG2SC-125-SS
-
CountryUSA
-
FinishPlain
-
MaterialStainless Steel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size1/4-28 UN-3A x 3/4 in
-
Width1/2 in
-
SeriesG2SC
-
Inside Diameter1-1/4 in
-
Outside Diameter2-1/16 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A582|ASTM F837 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-125-2-SSS Industry Standard Clamping Collar, 2-Piece Construction, 1-1/4 in ID x 2-1/16 in OD x 1/2 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. The BMU bearings are commonly referred to as thrust bearings. These bearings have a 40 deg contact angle to accept heavy axial loads. The bearings have Universally Flush Ground rings to facilitate mounting in multiple bearing sets. The inner and outer rings have identical widths. These bearings can be mounted as DB, DF and DT pairs or can be combined into triplex and quadraplex sets. When two bearings are mounted together, a clearance or preload may be obtained without the use of shims or spacers. This bearing has a machined brass cage and is not available with seals or shields. These bearings are most commonly used in vertical pump and motor applications.
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Drillco 76A120C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 5/16 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 5/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
Browning® 1296441 T45L Automatic Torque Limiter, 1-1/8 in Finished Bore, 4-1/2 in OD, 2800 in-lb (1-Spring)/4900 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
Moline Bearing 19321112 Type E Pillow Block Bearing, 1-3/4 in Dia Bore, 6-11/16 in L Bolt Center-to-Center, 2-1/4 in Base to Bore Centerline, 8-7/8 in OAL x 4-1/2 in OAH
Made of Cast Iron, this Solid Type E 2-Bolt Pillow Block is a Non-Expansion Mounted Roller Bearing Bearing with a 1 3⁄4 in (1.7500 in) shaft size. Includes a Steel Set Screw Locking Insert with a Double Collar, an available Standard V-Guard Contact Seal made of Nitrile, and a Standard Painted finish, this bearing is ready for even the toughest of jobs.
