Dodge® 023021 307 Type E-Xtra Pillow Block Roller Bearing Unit, 3-7/16 in Dia Bore, 10.81 to 11.19 in L Bolt Center-to-Center, 3-3/4 in Base to Bore Centerline, 14 in OAL 7-1/2 in OAH
Dodge® 023021 307 Type E-Xtra Pillow Block Roller Bearing Unit, 3-7/16 in Dia Bore, 10.81 to 11.19 in L Bolt Center-to-Center, 3-3/4 in Base to Bore Centerline, 14 in OAL x 7-1/2 in OAH
-
BrandDodge®
-
UPC782475699070
-
Manufacturer Part Number023021
-
CountryUSA
-
Load Capacity17750 lb Dynamic/108600 lb Static
-
Locking Device65 deg Set Screw
-
FinishBlack Oxide
-
MaterialCast Iron
-
Maximum Speed1640 rpm
-
TypeType E-Xtra
-
Mounting TypeTwo-Bolt Base
-
Seal TypeTrident™ Triple Lip
-
Series307
-
Base Width3-1/2 in
-
Base to Bore Centerline3-3/4 in
-
Bolt Center-to-Center Length10.81 to 11.19 in
-
Bore Diameter3-7/16 in
-
Bore TypeRound
-
Expansion TypeNon-Expansion (Fixed)
-
Overall Height7-1/2 in
-
Overall Length14 in
-
Overall Width5 in
- Case hardened rollers and races
- Factory assembled, adjusted and prelubricated
- Triple rubber lip contacting seals
- Easy installation and maintenance
| Competitor Name | Cross-Reference Number |
|---|---|
| Applied Industrial Technologies | 101874927 |
| Motion Industries | 00570460 |
-
Alternative Part NumberP2B-E-307R|23021
-
UNSPSC31171516
-
Package DescriptionEACH
-
Standards/ApprovalsUL Listed
-
Specification Sheet
-
Line Drawing
-
Catalog
-
Line Drawing
-
Instruction/Installation Manual
Recently Viewed
Dodge® 023021 307 Type E-Xtra Pillow Block Roller Bearing Unit, 3-7/16 in Dia Bore, 10.81 to 11.19 in L Bolt Center-to-Center, 3-3/4 in Base to Bore Centerline, 14 in OAL 7-1/2 in OAH
Dodge® 023021 307 Type E-Xtra Pillow Block Roller Bearing Unit, 3-7/16 in Dia Bore, 10.81 to 11.19 in L Bolt Center-to-Center, 3-3/4 in Base to Bore Centerline, 14 in OAL x 7-1/2 in OAH
Electrical Outlet Strips
Dodge® 041860 Type USAF Pillow Block Roller Bearing Unit, 2-7/16 in Dia Bore, 8.63 to 9.63 in L Bolt Center-to-Center, 11.13 in OAL x 6.44 in OAH
Dodge® 041860 Type USAF Pillow Block Roller Bearing Unit, 2-7/16 in Dia Bore, 8.63 to 9.63 in L Bolt Center-to-Center, 11.13 in OAL x 6.44 in OAH
ASP-125-2-SSS Industry Standard Clamping Collar, 2-Piece Construction, 1-1/4 in ID x 2-1/16 in OD x 1/2 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. The BMU bearings are commonly referred to as thrust bearings. These bearings have a 40 deg contact angle to accept heavy axial loads. The bearings have Universally Flush Ground rings to facilitate mounting in multiple bearing sets. The inner and outer rings have identical widths. These bearings can be mounted as DB, DF and DT pairs or can be combined into triplex and quadraplex sets. When two bearings are mounted together, a clearance or preload may be obtained without the use of shims or spacers. This bearing has a machined brass cage and is not available with seals or shields. These bearings are most commonly used in vertical pump and motor applications.
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3750239 Taper Bore Bushing, 2-1/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
