Gates® Power Transmission PowerGrip® HTD® 510-3M-09 Synchronous Belt, 9 mm W, 510 mm OAL, 3 mm Pitch, 170 Teeth, Neoprene
PowerGrip® HTD® belts have a larger, more robust tooth profile for increased capacity, as compared to timing belts.
-
BrandGates® Power Transmission
-
UPC072053892345
-
Manufacturer Part Number510-3M-09
-
CountryUSA
-
Pitch3 mm
-
Temperature Range-30 to 180 deg F
-
MaterialNeoprene
-
Tooth ProfileCurved
-
Reinforced MaterialFiberglass
-
Width9 mm
-
Series9293
-
Number of Teeth170
-
Overall Length510 mm
- Fiberglass tensile cord provides high strength, excellent flex life and high resistance to elongation
- Nylon tooth facing provides a durable wear surface for long service life
- Eliminates lubrication and re-tensioning to reduce maintenance and labor required on drives
- Neoprene body provides protection against grime, grease, oil and moisture
- Thirty percent increase in horsepower ratings, as compared to traditional timing belts
-
Alternative Part Number92932255
-
UNSPSC26111811
-
Package DescriptionEACH
-
Standards/ApprovalsRMA Standard
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission PowerGrip® HTD® 510-3M-09 Synchronous Belt, 9 mm W, 510 mm OAL, 3 mm Pitch, 170 Teeth, Neoprene
PowerGrip® HTD® belts have a larger, more robust tooth profile for increased capacity, as compared to timing belts.
Gates® Power Transmission PowerGrip® GT®3 880-8MGT-30 Synchronous Belt, 30 mm W, 880 mm OAL, 8 mm Pitch, 110 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
Enable fast, easy and secure 45°directional changes in conduit runs and allow for design configuration changes with Topaz's Schedule 40 PVC 45° Bell End Elbows. A standard conduit bell comprises one end of elbow with the opposite finished in a spigot or plain end. Suitable for above or below ground use and in concrete casement; cULus approved in sizes from 1/2” to 6.”
Gates® Power Transmission PowerGrip® HTD® 280-5M-15 Synchronous Belt, 15 mm W, 280 mm OAL, 5 mm Pitch, 56 Teeth, Neoprene
PowerGrip® HTD® belts have a larger, more robust tooth profile for increased capacity, as compared to timing belts.
Gates® Power Transmission PowerGrip® GT®3 750-5MGT-25 Synchronous Belt, 25 mm W, 750 mm OAL, 5 mm Pitch, 150 Teeth, Neoprene
The PowerGrip® GT®3 belt has twice the load carrying capacity of its predecessor HTD®. In addition, less width is required compared to HTD®, allowing lighter, more compact drives.
Gates® Power Transmission PowerGrip® GT®3 560-8MGT-30 Synchronous Belt, 30 mm W, 560 mm OAL, 8 mm Pitch, 70 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
