Southwire - Topaz 1260 Compression Bell End Elbow, 4 in Trade, 45 deg, PVC
Enable fast, easy and secure 45°directional changes in conduit runs and allow for design configuration changes with Topaz's Schedule 40 PVC 45° Bell End Elbows. A standard conduit bell comprises one end of elbow with the opposite finished in a spigot or plain end. Suitable for above or below ground use and in concrete casement; cULus approved in sizes from 1/2” to 6.”
-
BrandSouthwire - Topaz
-
UPC751338231856
-
Manufacturer Part Number1260
-
CountryUSA
-
MaterialPVC
-
Radius16 in
-
Trade Size4 in
-
TypeCompression
-
Angle45 deg
- A section of Schedule 40 PVC conduit which has been heated and bent to enable a 45 directional change in a conduit run
- A standard conduit bell is formed on one end while the other end is a spigot (plain) end
- Both ends are solvent weld
-
Alternative Part Number18198658
-
UNSPSC39131717
-
IDEA Index ID18198658
-
Package DescriptionEACH
-
Standards/ApprovalsUL 514B|UL E170258|cULus Listed|Federal Specification A-A-50563|NEMA/ANSI FB-1|Military Specification Number W-F-406D, W-F-406E, W-F-408D, W-S-610D
-
Warranty1 Year
-
Warranty Information
-
Catalog
-
Specification Sheet
Recently Viewed
Enable fast, easy and secure 45°directional changes in conduit runs and allow for design configuration changes with Topaz's Schedule 40 PVC 45° Bell End Elbows. A standard conduit bell comprises one end of elbow with the opposite finished in a spigot or plain end. Suitable for above or below ground use and in concrete casement; cULus approved in sizes from 1/2” to 6.”
Gates® Power Transmission PowerGrip® HTD® 280-5M-15 Synchronous Belt, 15 mm W, 280 mm OAL, 5 mm Pitch, 56 Teeth, Neoprene
PowerGrip® HTD® belts have a larger, more robust tooth profile for increased capacity, as compared to timing belts.
Gates® Power Transmission PowerGrip® GT®3 750-5MGT-25 Synchronous Belt, 25 mm W, 750 mm OAL, 5 mm Pitch, 150 Teeth, Neoprene
The PowerGrip® GT®3 belt has twice the load carrying capacity of its predecessor HTD®. In addition, less width is required compared to HTD®, allowing lighter, more compact drives.
Gates® Power Transmission PowerGrip® GT®3 560-8MGT-30 Synchronous Belt, 30 mm W, 560 mm OAL, 8 mm Pitch, 70 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
Gates® Power Transmission PowerGrip® GT®3 4578-14MGT-85 Synchronous Belt, 85 mm W, 4578 mm OAL, 14 mm Pitch, 327 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
Gates® Power Transmission PowerGrip® HTD® 710-5M-15 Synchronous Belt, 15 mm W, 710 mm OAL, 5 mm Pitch, 142 Teeth, Neoprene
PowerGrip® HTD® belts have a larger, more robust tooth profile for increased capacity, as compared to timing belts.
