ASP-872-S Industry Standard Clamping Collar, 2-Piece Construction, 7/8 in ID x 1-5/8 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630778
-
Manufacturer Part NumberG2SC-087-B
-
CountryUSA
-
FinishBlack Oxide
-
MaterialSteel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size1/4-28 UN-3A x 5/8 in
-
Width1/2 in
-
SeriesG2SC
-
Inside Diameter7/8 in
-
Outside Diameter1-5/8 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A108|ASTM A574 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-872-S Industry Standard Clamping Collar, 2-Piece Construction, 7/8 in ID x 1-5/8 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
1/2" -FEMALE PIPE THREADX1/4" -FEMALE PIPE THREAD BLACK REDUCER-JPW1/2X1/4BR >
1-1/4" ELECTRICAL STRUT CLAMPS-JWH511587>
Browning® 1228865 Finished Bore Straight Miter Gear With Hardened Teeth, Keyway and Setscrew, 1 in Dia Bore
Bevel and miter gearing is a form of gearing in which the tooth-bearing surfaces are the faces of the gears rather than the edges. In bevel and miter gearing, the gears are cone shaped. This allows the edges of the mating gears to mesh and transmit torque. The geometry of the mesh creates a 90 deg angle. As a result, this type of gearing is suitable for applications where a change of direction is required. Other designs exist to create other angles however 90 deg serves the majority of applications. In bevel and miter gearing the input and output shaft are intersecting. It is typical for bevel and miter gear reducers to have lower reduction ratios. For example, 5:1 and lower are typical and they are different than other types of gearing. Two types of bevel and miter gearing are typical. These are straight and spiral. As the name implies, the teeth of straight bevel gears are cut straight. This means that the teeth are oriented perpendicular to the outside edge of the gear. The teeth on spiral bevel gears are cut at an angle to the outside edge of the gear. This type of gearing is said to have "helical" teeth and the angle is called the "helix" angle. Bevel and miter gearing have proven reliable for many years. The use of this type of gearing extends across many industries. Some of these include food processing, woodworking, paper and textile.
SWIFFER WETJET PAD REFILLS--BX/12-PG-32698>
Dichtomatik N70326 O-Ring, 326 Dash Number, 1.6 in ID x 2.02 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
