ASP-100-2-S Industry Standard Clamping Collar, 2-Piece Construction, 1 in ID x 1-3/4 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630747
-
Manufacturer Part NumberG2SC-100-B
-
CountryUSA
-
FinishBlack Oxide
-
MaterialSteel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size1/4-28 UN-3A x 5/8 in
-
Width1/2 in
-
SeriesG2SC
-
Inside Diameter1 in
-
Outside Diameter1-3/4 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A108|ASTM A574 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-100-2-S Industry Standard Clamping Collar, 2-Piece Construction, 1 in ID x 1-3/4 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
3" PALMYRA PAINT BRUSHES-CCA1030F >
Browning® 3749199 Taper Lock Bushing, 1-9/16 in Dia Bore, 2-1/4 in Dia Barrel, 1-1/2 in OAL, Steel
Browning® 3749199 Taper Lock Bushing, 1-9/16 in Dia Bore, 2-1/4 in Dia Barrel, 1-1/2 in OAL, Steel
Gates CX-85 Tri-Power® Industrial V-Belts - CX Section, 7/8 in Top Width, 1 Strand, 89.0000 in Nominal Outside Length, Cogged
Most traditional v-belts struggle with small spaces and cause frequent interruptions, leading to costly downtime. Reduce these common drive issues with Tri-Power, your tried-and-true classical section replacement V-belt. The Tri-Power bandless V-belt is specifically designed to tackle the challenges associated with small sheave diameters on existing drives. Whether powering compressors, pumps, or other critical equipment, this belt ensures that your machinery runs efficiently and reliably. The advantage of this bandless V-belt lies in its ability to provide a like-for-like replacement without the need for full-system replacements. Its advanced design not only suits small sheaves but also enhances power transmission and reduces maintenance needs. Choose Gates Tri-Power V-belts for a dependable high-quality solution that keeps your existing drives running longer without interruptions.
Browning® 1045541 VP Series Type 2 Variable Pitch Sheave, 1-1/8 in Finished Bore, 6 in OD, 1 Groove, 4.4 to 5.4 in (A/4L)/4.7 to 5.9 in (B/5L/5V) Dia Pitch, 7/8 to 1-1/4 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
Rust-Oleum High Performance 2300 System Inverted Striping Spray Paint creates bright, sharp and long-lasting lines for a variety of surfaces. This oil-based paint is ideal for parking lots, warehouse aisles, pallet positions, stadiums and more.
