SP-343-2-S Industry Standard Clamping Collar, 2-Piece Construction, 3-7/16 in ID x 4-3/4 in OD x 7/8 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861634646
-
Manufacturer Part NumberG2SC-343-B
-
CountryUSA
-
FinishBlack Oxide
-
MaterialSteel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size3/8-24 UN-3A x 1 in
-
Width7/8 in
-
SeriesG2SC
-
Inside Diameter3-7/16 in
-
Outside Diameter4-3/4 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A108|ASTM A574 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
SP-343-2-S Industry Standard Clamping Collar, 2-Piece Construction, 3-7/16 in ID x 4-3/4 in OD x 7/8 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
1/4" -SHANK WIRE CUP BRUSH-JWH345380 >
The M12™ HAMMERVAC™ Universal Dust Extractor is a universal solution for eliminating dust when drilling with any SDS Plus rotary hammer. It is the industry's only onboard universal dust extractor. The universal side handle allows for operation with any SDS Plus hammer in the industry: corded, cordless, Milwaukee Brand or other. The AUTOPULSE™ filter cleaning mechanism will clean the filter automatically after use, allowing for OSHA Table One Compliance. This extractor allows users to drill up to 8" in depth and up to 1-1/4" in diameter with two accessory nozzles designed for small and large diameters. The adjustable depth stop allows for quickly and accurately setting the desired hole depth. The dust box can be emptied with no exposure by hooking it up to a large dust extractor to vacuum out the dust. The tool also features an Auto On/Off Mode that saves time and battery life. The M12™ HAMMERVAC™ runs off of any Milwaukee M12™ REDLITHIUM™ Battery to be a fully self-powered unit.
Jones Stephens™ D06750 Dielectric Union, 3/4 in, MNPT x Solder, Forged Steel, Domestic
BBI 087432 Fully Threaded Cap Screw, 5/8-11, 2 in L Under Head, 5 Grade, Carbon Steel, Zinc CR+3
BBI 087432 Fully Threaded Cap Screw, 5/8-11, 2 in L Under Head, 5 Grade, Carbon Steel, Zinc CR+3
