ASP-502-S Industry Standard Clamping Collar, 2-Piece Construction, 1/2 in ID x 1-1/8 in OD x 13/32 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630679
-
Manufacturer Part NumberG2SC-050-B
-
CountryUSA
-
FinishBlack Oxide
-
MaterialSteel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size8-32 UN-3A x 1/2 in
-
Width13/32 in
-
SeriesG2SC
-
Inside Diameter1/2 in
-
Outside Diameter1-1/8 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A108|ASTM A574 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-502-S Industry Standard Clamping Collar, 2-Piece Construction, 1/2 in ID x 1-1/8 in OD x 13/32 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Dodge® 023692 407 Type E-Xtra Pillow Block Roller Bearing Unit, 4-7/16 in Dia Bore, 13-1/4 to 13-3/4 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 16.63 in OAL 9.28 in OAH
Dodge® 023692 407 Type E-Xtra Pillow Block Roller Bearing Unit, 4-7/16 in Dia Bore, 13-1/4 to 13-3/4 in L Bolt Center-to-Center, 4-3/4 in Base to Bore Centerline, 16.63 in OAL x 9.28 in OAH
Browning® 1296359 Automatic Torque Limiter, 7/8 in Straight Bore, 2-1/2 in OD, 800 in-lb (1 Spring)/1100 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
Browning® 3748498 Taper Lock Bushing, 11/16 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
Browning® 3748498 Taper Lock Bushing, 11/16 in Dia Bore, 1.511 in Dia Barrel, 7/8 in OAL, Steel
ASP-162-2-S Industry Standard Clamping Collar, 2-Piece Construction, 1-5/8 in ID x 2-5/8 in OD x 11/16 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Browning® 1296458 T45L Automatic Torque Limiter, 1-3/16 in Finished Bore, 4-1/2 in OD, 2800 in-lb (1-Spring)/4900 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
