FYH® SAA209 28FP7 SAA Cylindrical Ball Bearing Insert, 1-3/4 in Dia Bore, 3.34 in OD, 1.72 in W, 34.1 kN Dynamic/21.3 kN Static Load
FYH® SAA209 28FP7 SAA Cylindrical Ball Bearing Insert, 1-3/4 in Dia Bore, 3.34 in OD, 1.72 in W, 34.1 kN Dynamic/21.3 kN Static Load
-
BrandFYH®
-
Manufacturer Part NumberSAA209 28FP7
-
CountryUSA
-
Load Capacity34.1 kN Dynamic/21.3 kN Static
-
Closure TypeEccentric Locking Collar
-
TypeCylindrical
-
Width1.72 in
-
SeriesSAA
-
Outside Diameter3.34 in
-
Bore Diameter1-3/4 in
Recently Viewed
FYH® SAA209 28FP7 SAA Cylindrical Ball Bearing Insert, 1-3/4 in Dia Bore, 3.34 in OD, 1.72 in W, 34.1 kN Dynamic/21.3 kN Static Load
FYH® SAA209 28FP7 SAA Cylindrical Ball Bearing Insert, 1-3/4 in Dia Bore, 3.34 in OD, 1.72 in W, 34.1 kN Dynamic/21.3 kN Static Load
Proto® J291R Locking Plier, 1-1/8 in, 1/2 in THK Straight Alloy Steel Jaw
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. The BMU bearings are commonly referred to as thrust bearings. These bearings have a 40 deg contact angle to accept heavy axial loads. The bearings have Universally Flush Ground rings to facilitate mounting in multiple bearing sets. The inner and outer rings have identical widths. These bearings can be mounted as DB, DF and DT pairs or can be combined into triplex and quadraplex sets. When two bearings are mounted together, a clearance or preload may be obtained without the use of shims or spacers. This bearing has a machined brass cage and is not available with seals or shields. These bearings are most commonly used in vertical pump and motor applications.
2 RAISED FACE THREADED FLANGES
Milwaukee® 49-56-7055 Large Thread Quick-Change Universal Hole Saw Arbor, 1-1/4 in and Larger Arbor, 7/16 in, Alloy Steel/Hardened Carbon Steel
This Milwaukee hole saw arbor has a 7/16 in. hex shank for greater gripping capability in the chuck. The backing plate is equipped with push pins which lock into holes on the backing plate of the hole saw for positive efficient transmission of torque. It can be used in 1/2 in. capacity drills and larger. The arbor has a 5/8 - 18 thread and can be used on hole saws from 1-1/4 in. and larger. It can be used with (49-56-8000), (49-56-8002) and (49-56-8005) pilot bits. Pilot bit (49-56-8000) is supplied with this arbor for use on wood and metal. One arbor and pilot per package.
BBI 847446 Partially Threaded Cap Screw, 5/8-11, 4 in L Under Head, 5 Grade, Medium Carbon Steel, Zinc CR+3
BBI 847446 Partially Threaded Cap Screw, 5/8-11, 4 in L Under Head, 5 Grade, Medium Carbon Steel, Zinc CR+3
