Sloan Valves ROYAL #110-4.5 TOILET VLAVE 4.5GPF SLO 3910004
Sloan® Royal® 3910004 110 Single-Flush Manual Exposed Flushometer, 4 gpf, 1 in IPS Inlet, 1-1/2 in Spud, 15 to 80 psi, Polished Chrome
-
BrandSloan®
-
UPC671254111905
-
Manufacturer Part Number3910004
-
CountryUSA
-
Finish/ColorPolished Chrome
-
MaterialSemi-Red Brass
-
Fixture TypeWater Closet
-
Pressure Rating15 to 80 psi
-
TypeSingle-Flush
-
Handle TypeNon-Hold Open Oscillating
-
Series110
-
Inlet Size1 in IPS
- Flush volumes start as low as 1.6 gpf/6.0 lpf
- Water conservation is aided by the ADA Compliant, non-hold-open handle, which prevents toilet from exceeding intended flush volume
- Flush accuracy is controlled by CID™ technology, also enhancing water efficiency
- Integrity of the product is maintained with the vandal resistant stop cap
- Durability is facilitated with high copper, low zinc brass castings for dezincification resistance
- Adjustable tailpiece
- Permex® synthetic rubber diaphragm with dual filtered fixed by-pass
- Valve body, cover, tailpiece and control stop shall be in compliance with ASTM alloy classification for semi-red brass
- Exposed water closet flushometer, for floor mounted or wall hung top spud bowls
| Competitor Name | Cross-Reference Number |
|---|---|
| Ferguson | S3910004 |
-
Alternative Part Number110-4.5
-
UNSPSC40141640
-
Standards/ApprovalsADA Compliant|ASTM Specified|ASSE1037 Valve|BAA Compliant
-
Specification Sheet
-
Line Drawing
-
Instruction/Installation Manual
Recently Viewed
Sloan® Royal® 3910004 110 Single-Flush Manual Exposed Flushometer, 4 gpf, 1 in IPS Inlet, 1-1/2 in Spud, 15 to 80 psi, Polished Chrome
BBI 042450 Partially Threaded Cap Screw, 5/8-11, 5 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
BBI 042450 Partially Threaded Cap Screw, 5/8-11, 5 in L Under Head, 8 Grade, Alloy Steel, Zinc Yellow Bake CR+6
Browning® 1045491 VP Series Type 2 Variable Pitch Sheave, 7/8 in Finished Bore, 5.35 in OD, 1 Groove, 3.9 to 4.7 in (3L)/4.2 to 5.2 in (A/4L)/4.4 to 5.4 in (B/5L) Dia Pitch, 3/4 to 1-1/8 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
3/8" X 3" M/D OVAL DIE SPRINGS-LANSMDO375300 >
2-1/2" CARLON PVC LB UNILETS-JWH515825 >
Stanley Proto J1220M-T500 Combination Wrench 20mm ASD Fully Polished 12 Point
Stanley Proto J1220M-T500 Combination Wrench 20mm ASD Fully Polished 12 Point-PROJ1220MT500
