Reliance Worldwide Corporation

This is a CxC (Cup x Cup) coupling with rolled stop designed for use in commercial and residential systems. It is mainly utilized as an above the ground fitting to join and solder water supply piping. This straight coupling is built of copper with sweat sockets on both ends to create a union between 1/2 in. ID (5/8 in. OD) straight lends of a pipe. This copper fitting meets NSF standards and complies with Lead-Free law for safe water drinking.

The Eastman Slip-Joint Washer is constructed of a high-impact polyethylene plastic for a long-lasting durability. The white washer measures 1-1/2 inch. Designed for use in tubular drain applications, the washer works in conjunction with a slip-joint nut (not included) to seal the connection between PVC pipes to prevent leakage. Sold and priced 100 per order.

The PI Range of inch-size push-in fittings is offered for tube sizes 5/32 to 5/8 in OD. The fittings are manufactured in gray acetal copolymer with food grade nitrile O-Ring, making them especially suitable for applications involving foodstuff and potable liquids. They are also suitable for air and inert gases and can therefore be used on CO2 lines, pneumatic applications and vacuum.

The Speedfit secure range of fittings ensures a secure connection when adapting Speedfit Pipe or copper to threaded applications. To install, always use PTFE tape when preparing thread (refer to tape manufacturers recommendations), working up the full thread length. The fitting can be tightened using a spanner on the hexagon area at the middle of the component. Do not over-tighten the fitting. To lock pipe in place, push the pipe into the fitting and turn the nut clockwise. Should the need arise to release the pipe, turn the locking nut anti-clockwise, push the collet towards the fitting and pull the pipe to release.

The Speedfit secure range of fittings ensures a secure connection when adapting Speedfit Pipe or copper to threaded applications. To install, always use PTFE tape when preparing thread (refer to tape manufacturers recommendations), working up the full thread length. The fitting can be tightened using a spanner on the hexagon area at the middle of the component. Do not over-tighten the fitting. To lock pipe in place, push the pipe into the fitting and turn the nut clockwise. Should the need arise to release the pipe, turn the locking nut anti-clockwise, push the collet towards the fitting and pull the pipe to release.

An innovative push-fit fitting which provides a quick and easy method of replacing burst or damaged pipe without the need to alter existing pipe work. See below for a step by step installation guide.

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods.

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods.

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods.

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40% when compared to traditional fixing methods.

Push-fit fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. A must for any tool bag. The unique feature of the Speedfit Concept, the ability to disconnect the fitting at will, means that the End Cap provides a leak proof seal and can be removed at any stage in order to allow work to restart or allow an extension to the system. This makes the fitting the perfect tool for when water needs to be turned back on, overnight for instance, or if a job suffers an interruption. End Caps are also useful when pressure testing a system before appliances are connected. Simply push the fitting fully on to the pipe. Should the need arise to demount the connection push the collet towards the body of the fitting and pull the pipe to release.

Push-fit fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. A must for any tool bag. The unique feature of the Speedfit Concept, the ability to disconnect the fitting at will, means that the End Cap provides a leak proof seal and can be removed at any stage in order to allow work to restart or allow an extension to the system. This makes the fitting the perfect tool for when water needs to be turned back on, overnight for instance, or if a job suffers an interruption. End Caps are also useful when pressure testing a system before appliances are connected. Simply push the fitting fully on to the pipe. Should the need arise to demount the connection push the collet towards the body of the fitting and pull the pipe to release.

The JG CTS Shut-off valve ensures an immediate water supply cut-off with a simple turn of the valve handle. The valve is designed to work with both copper and Speedfit plastic pipe. To lock the pipe in place, simply push the pipe into the fitting and turn the nut clockwise. Should the need arise to release the pipe, turn the locking nut anti-clockwise, push the collet towards the fitting and pull the pipe to release.

The JG CTS Shut-off valve ensures an immediate water supply cut-off with a simple turn of the valve handle. The valve is designed to work with both copper and Speedfit plastic pipe. To lock the pipe in place, simply push the pipe into the fitting and turn the nut clockwise. Should the need arise to release the pipe, turn the locking nut anti-clockwise, push the collet towards the fitting and pull the pipe to release.

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40 percent when compared to traditional fixing methods.

Push-fit plastic fitting for the connection of plastic, copper, and CPVC pipe. Designed, manufactured and assembled by John Guest Speedfit. Simply push the fitting fully onto the pipe and twist the plastic nut clockwise to lock in place. Should the need arise to demount the connection unlock the nut and push the collet towards the body of the fitting and pull the pipe to release. The fitting ensures an easier working environment in confined places, is approved for behind the wall installations, and removes the need for hot works on site. Installation can be reduced by around 40 percent when compared to traditional fixing methods.

The SharkBite Water Heater Installation Kit is designed to simplify water heater installation. The kit features special push-fit fittings that allow the user to easily connect water distribution pipe.

Sharkbite® Angle Stops combine push-fit technology with an angle stop quarter turn valve. This allows the valve to control water flow to household plumbing fixtures, and provides easy shut-off of water flow for maintenance and repair, if necessary. These valves require no solder, clamps, unions or glue. The push-to-connect end allows you to push on to Copper, PEX, CPVC or PE-RT pipe easily. This product can be easily rotated after assembly for easy installation, even in tight spaces.

Sharkbite® Straight Stops combine push-fit technology with a straight stop quarter turn valve. This allows the valve to control water flow to household plumbing fixtures, and provides easy shut-off of water flow for maintenance and repair, if necessary. These valves require no solder, clamps, unions or glue. The push-to-connect end allows you to push on to Copper, PEX, CPVC or PE-RT pipe easily. This product can be easily rotated after assembly for easy installation, even in tight spaces.

SharkBite® U280 Elbow 1/2 in MNPT x 1/2 in. The Elbow allows you to easily add another line off of existing plumbing. It can be used to connect to CPVC, copper or PEX tubing. Simply cut the pipe and push on the fitting. SharkBite® fittings can easily be removed and are reusable.

SharkBite's Braided Flexible Water Heater Connectors are great for easily connecting your hot and cold water supply lines to your water heater. Simply apply pipe thread to the MIP nipples on the water heater and then thread the female connection on the connector to the nipple and tighten with channel locks or a similar tool. These hoses are also available in Corrugated Stainless Steel and are also available with an integrated Ball Valve.

SharkBite's Braided Flexible Water Heater Connectors are great for easily connecting your hot and cold water supply lines to your water heater. Simply apply pipe thread to the MIP nipples on the water heater and then thread the female connection on the connector to the nipple and tighten with channel locks or a similar tool. These hoses are also available in Corrugated Stainless Steel and are also available with an integrated Ball Valve.

SharkBite® End Caps are push-to-connect and are the easiest way to cap off your Copper, PEX, CPVC or PE-RT pipe lines. There is no soldering, clamps, unions or glue required. These fittings are great for stub outs and pressure testing a home as they take no time to cure. They are easily removed with a Disconnect Clip. All SharkBite® fittings are capable of being installed on either wet or dry pipe. This product is rated for up to 200 psi and 200 deg F.

SharkBite's Threaded Adapters are FNPT on one end, and allow the user to connect any appropriately sized SharkBite push-to-connect fitting on the other end. To connect the SharkBite fitting, simply push the copper tube size (CTS) end into the SharkBite fitting. This fitting is designed for potable water and radiant heating (including underground or behind-the-wall) applications with no access panels required. It is rated up to 200 deg F and 200 psi.