Milwaukee Tool
Milwaukee 1-1/4" X 16" SPLINE ROTOHAMMER BIT MWK 48-20-4125
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/4"X22" SPLINE R/HAMM BIT MWK 48-20-4126
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/8" SELF-FEED BITS MWK 48-25-1121
Milwaukee® selfeed drill bits deliver speed and Endurance for repetitive drilling of large holes. Designed for any trade that demands woodcutting for installing pipe and conduit, selfeed bits feed into work without pressure and provide faster boring of clean, accurate holes. The bits have improved balance with reduced runout, while the hex shank provides a secure gripping surface for the drill chuck. Every Milwaukee® selfeed drill bit is coated with a rust inhibitor. Built to last and designed to perform, these selfeed bits are resharpenable so you can keep them cutting like new.
Milwaukee 1-1/8" X 16" SPLINE ROTOHAMMER BIT MWK 48-20-4112
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-1/8"X22" SPLINE R/HAMM BIT MWK 48-20-4113
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-3/4" SELF-FEED BITS MWK 48-25-1751
Milwaukee® selfeed drill bits deliver speed and Endurance for repetitive drilling of large holes. Designed for any trade that demands woodcutting for installing pipe and conduit, selfeed bits feed into work without pressure and provide faster boring of clean, accurate holes. The bits have improved balance with reduced runout, while the hex shank provides a secure gripping surface for the drill chuck. Every Milwaukee® selfeed drill bit is coated with a rust inhibitor. Built to last and designed to perform, these selfeed bits are resharpenable so you can keep them cutting like new.
Milwaukee 1-3/8" CARBIDE-TOOTH HOLESAW MWK 49-56-1373
Milwaukee® carbide tipped hole saws provide long life and faster cutting in cement board, ceramic tiles, fiberglass and wood products such as fiberboard, flake board and plywood. Use a carbide tipped pilot bit (49-56-8005) when cutting ceramic tile, brick and other abrasive materials.
Milwaukee 1-3/8" X 16" SPLINE R/H BITS MWK 48-20-4137
Two cutter spline bits have a series of 12 spline that slide into an equal but opposite set of spline in the drive system of the spline drive hammer. This positive engagement of spline to spline allows maximum transmission of energy from the hammer to the bit. Superior quality Carbide nibs are vacuum brazed to a heat treated steel body resulting in two cutting edges which pulverize the concrete as the bit turns and pounds the work surface. Available from 3/8 in. to 1-1/2 in. diameters as well as metric diameters. One per package.
Milwaukee 1-3/8"X22" SPLINE R/HAMM BIT MWK 48-20-4138
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1-5/8" STEEL HAWG CUTTER MWK 49-57-1627
Drill holes up to 3X faster and enjoy fast change-outs with the Milwaukee® 1-5/8 in. quick change tang drive Steel Hawg® cutter. This long-lasting cutter features Carbide teeth and an alternating cutting pattern to cut up to a 1 in. hole depth in steel, stainless steel, cast iron or aluminum. It leaves a ream-like finish without pre-punching or pilot holes. The Steel Hawg cutter works with most electromagnetic drill presses. Use it with arbor 49-57-0012 or 49-57-0013 on Milwaukee's 4292-1 or 4297-1 magnetic drill press or arbor 49-57-0032 on Milwaukee's 4262-1 mag press.
Milwaukee 1-9/16" STEEL HAWG CUTTERS MWK 49-57-1564
Drill holes up to 3X faster and enjoy fast change-outs with the Milwaukee® 1-9/16 in. quick change tang drive Steel Hawg® cutter. This long-lasting cutter features Carbide teeth and an alternating cutting pattern to cut up to a 1 in. hole depth in steel, stainless steel, cast iron or aluminum. It leaves a ream-like finish without pre-punching or pilot holes. The Steel Hawg cutter works with most electromagnetic drill presses. Use it with arbor 49-57-0012 or 49-57-0013 on Milwaukee's 4292-1 or 4297-1 magnetic drill press or arbor 49-57-0032 on Milwaukee's 4262-1 mag press.
Milwaukee 1.8" SPOT INFRARED CAMERAS MWK 2257-20
Designed from the ground up with the professional tradesman in mind, the 102 x 77 spot infrared Imager gives users unmatched visibility to maintenance issues, so they can quickly diagnosis the problem. With instant start-up for scanning large areas and the ability to give high resolution images with precise single spot measurements, the new Imager is ideal for fast and accurate troubleshooting. Exclusive dual sense technology allows the Imager to individually optimize pixels to eliminate the blurring of hot and cold details in complex environments. Equipped with 56:1 distance to spot performance, a 15 sec image hold and a temperature range of 14 to 626 deg F, users are able to scan, target and see a single on-screen temperature reading from long distance or from up close. Backed by a 5 years warranty, the 102 x 77 spot infrared Imager confirms Milwaukee® continued commitment to delivering solutions that save time and increase productivity for its users.
Milwaukee 1" CRIMP END BRUSH PKGD MWK 48-52-1020
1" CRIMP END BRUSH PACKAGED-MWK48521020 >
Milwaukee 1" DIA CONCRETE CORE BITS MWK 48-16-1006
1" DIAMOND CONCRETE CORE BITS-MWK48161006 >
Milwaukee 1" DIA CONCRETE CORE BITS MWK 48-16-1007
1" DIAMOND CONCRETE CORE BITS-MWK48161007 >
Milwaukee 1" LOCKING TUBING CUTTERS MWK 48-22-4202
The Milwaukee® tubing cutter cuts upto 1 in rubber and plastic tubing and PEX-a tubing. It features a replaceable V-shaped, double ground steel blade for clean perpendicular cuts and maximum tool life. The 1-handed locking mechanism is designed for an easy to use lock for improved tool safety. Backed by Milwaukee® Limited Lifetime Warranty the tubing cutter was built with an all metal core that provides longer tool life to the professional user.
Milwaukee 1" X 16" SPLINE ROTOHAMMER BITS MWK 48-20-4100
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1" X 22" SPLINE ROTOHAMMER BITS MWK 48-20-4101
Milwaukee®'s spline 2-cutter rotary hammer drill bits are used for drilling intro brick, block, and concrete.
Milwaukee 1" X 25' MAGNETIC-TIP TAPE MEASURE MWK 48-22-0325
The MILWAUKEE® 25ft Compact Magnetic Tape Measures have up to 15' of reach* and a magnet that easily attaches to EMT & steel studs. The tape is wear and impact-resistant with nylon blade protection and an additional anti-tear coating on the first 6” of the blade, reducing tape tear. The compact measuring tapes are constructed with a 5-point reinforced frame for impact resistance.
Milwaukee 1" X 35' MAGNETIC-TIP TAPE MEASURE MWK 48-22-0335
The MILWAUKEE® 35ft Compact Magnetic Tape Measures have up to 15' of reach* and a magnet that easily attaches to EMT & steel studs. The tape is wear and impact-resistant with nylon blade protection and an additional anti-tear coating on the first 6 in of the blade, reducing tape tear. The compact measuring tapes are constructed with a 5-point reinforced frame for impact resistance.
Milwaukee 1"X25-FT INCH TAPE MEASURES MWK 48-22-5525
Milwaukee® tape measures are nothing but heavy duty. Using nylon blade protection and a 5-point reinforced frame, they offer up to 10X longer life. Additional innovative features include a wider base which allows for greater stability during layout and an optimized hook that is designed for scoring applications like drywall.
Milwaukee 1/2" 120-V D-HANDLED DRILLS MWK 1107-6
The professional's choice for superior jobsite performance. With a powerful Milwaukee® built motor, trigger speed control and reverse, the 1/2 in D-handle drill helps you reach maximum productivity on the job. Helical cut, heat treated gears deliver quiet performance and extended tool life with wood, metal, plastics and composites. The durable glass-reinforced nylon D-handle and side-handle assist with a secure grip and extra control. The QUIK-LOK™ cord detaches easily for storage or service replacement. Use this 1/2 in D-handle drill with our right angle drive attachment for increased versatility.
Milwaukee 1/2" 120-V HAMMERDRILL KITS MWK 5387-22
The adaptable 1/2 in dual-speed hammer drill features an 8.5 A motor that provides overload protection, even when drilling 3/4 in holes in concrete. Choose controls in two ranges: 0 to 1000 rpm/0 to 16000 bpm or 0 to 2500 rpm/0 to 40000 rpm. It's versatile enough to drill in wood with flat boring bits, hole saws, auger bits and selfeed bits - or drill in steel with twist bits and in concrete with percussion bits. The removable side-handle helps you set the depth rod for preset hold drilling. The heavy duty metal gear case withstands daily jobsite use, yet the drill's lightweight balanced pistol-grip design reduces fatigue during a long work day. The 10-foot, QUIK-LOK™ cord and keyed chuck ensure hours of reliable, uninterrupted performance.
Milwaukee 1/2" 120-V HAMMERDRILLS MWK 5378-21
The power to drill 1/2 in. holes in concrete. The versatility to excel at wood and steel applications. This powerful 7.5 amp, 1/2 in. hammer drill features dual trigger speed control in two ranges, with more power for the toughest applications or more speed and less torque for lighter applications. Use it for drilling in wood with flat boring bits, hole saws, auger bits and Selfeed bits, or in steel with twist bits and in concrete with percussion bits. The removable side handle helps set the depth rod for pre-set hole drilling. The heavy-duty metal gear case withstands daily jobsite use, yet the drill's lightweight, balanced pistol-grip design reduces fatigue during a long work day. The kit includes a durable carrying case.
Recently Viewed
RETAINING RINGS ARE PRECISION-ENGINEERED COMPONENTS, WHICH WHEN APPLIED IN BORES PROVIDES A SHOULDER THAT ACCURATELY POSITIONS, LOCATES OR RETAINS OTHER PARTS OF AN ASSEMBLY. THEY CAN BE USED TO REPLACE PINS AND WASHERS, THREADED SECTIONS, COLLARS, MACHINE SHOULDERS, AND OTHER COSTLY OR TIME-CONSUMING METHODS
Browning® 1293570 Standard Riveted Roller Chain, 1 in Pitch, 5/8 in Dia x 5/8 in W Roller, Steel
STAINLESS STEEL 2-TOGGLE WALL PLATE - JWH511234 >
RIDGID® 31305 Hex Wrench, 1-1/8 to 2-5/8 in Pipe, 9-1/2 in OAL, Hex Jaw, Cast Iron Handle, Knurled Nut Adjustment
RIDGID® 31305 Hex Wrench, 1-1/8 to 2-5/8 in Pipe, 9-1/2 in OAL, Hex Jaw, Cast Iron Handle, Knurled Nut Adjustment
3/8" VSR 5-AMP 2500-RPM ELECTRIC DRILL-BD-D21007 >
#2021 7/8" BRASS CUP HOOKS-NTL119651 >
