THE MAGNETIC SOURCE™ 07542 Heavy Duty Holding and Retrieving Magnet, 150 lb Pull
Use to hold and position spray nozzles, hoses, temporary wiring and more. Great for retrieving hand tools and other metal items from waterways. Attach a rope or rod to magnet's eyebolt for retrieving. Hundreds of sporting, household, industrial and commercial uses. Eyebolt and nuts included.
-
BrandTHE MAGNETIC SOURCE™
-
UPC095421075423
-
Manufacturer Part Number07542
-
CountryUSA
-
Pull Capacity150 lb
-
TypeHeavy Duty
- Magnetic Shields™ to block magnetic strength when not in use
| Cross-Reference Number |
|---|
| 362662 |
-
UNSPSC27112109
Recently Viewed
THE MAGNETIC SOURCE™ 07542 Heavy Duty Holding and Retrieving Magnet, 150 lb Pull
Use to hold and position spray nozzles, hoses, temporary wiring and more. Great for retrieving hand tools and other metal items from waterways. Attach a rope or rod to magnet's eyebolt for retrieving. Hundreds of sporting, household, industrial and commercial uses. Eyebolt and nuts included.
Alemite® 1724-B 45 deg Thread Forming Fitting, 1/8 in Taper Thread, 0.83 in OAL, Steel, Trivalent Zinc Plated
Alemite thread forming fittings have special tapered drive threads which reshape the material in an untapped hole to provide a leak proof seal. They are most effectively installed by spinning into the untapped hole, but may be driven straight into the untapped hole. Thread forming fittings can be replaced by any standard threaded fitting or by another thread forming fitting.
Milwaukee® M18™ 2607-20 Cordless Hammer Drill/Driver, 1/2 in Metal Single Sleeve Ratcheting Lock Chuck, 18 V DC, 400/1800 rpm No-Load, Li-Ion Battery
The most compact hammer drill driver in its class is more powerful than the competition. Built with a Milwaukee® 4-pole frameless motor, the M18™ compact 1/2 in. drill driver delivers 500 in-lbs of torque and up to 1,800 RPM. At only 7-1/4 in. length, this drill driver allows you access to the tightest work spaces. An all-metal gear case and 1/2 in. metal chuck provide maximum durability, even on the most challenging work sites.
FLEX PBAND 14T-MLF90965 >
Milwaukee® 2105 6000 Penlight, LED Bulb, Aircraft Aluminum Housing, 100 Lumens, 1 Bulbs
The MILWAUKEE® Penlight delivers 100 lumens of output for Brighter, Clearer, Easier Inspections. The innovative protective rubber bite zone at the end of the light allows users to safely direct light while performing two-handed tasks. The LED penlight is IP67 rated, maiking waterproof, dustproof and the lens and 6000 series aircraft aluminum body are impact and corrosion-resistant. The penlight’s metal clip attaches to any chest or pant pocket for quick access and everyday use. Our TRUEVIEW™ High Definition output illuminates more of your work area with brighter natural light optimized for high color accuracy. The Milwaukee Penlight is covered by a limited lifetime warranty.
Milwaukee® 48-20-9045 SHOCKWAVE™ Single Ended Hammer Drill Bit, 3/4 in Drill Bit, 3/8 in 3-Flat Shank, 4 in D Cutting, Carbide Cutting Edge, 6 in OAL
The MILWAUKEE® Carbide Hammer Drill Bits are designed with sharpened carbide to deliver up to 9x longer life and 4x faster drilling into concrete. The POWER TIP™, available in sizes 3/8" and above, is designed with dynamic cutting edges and a chip breaker for increased productivity and easier drilling from start to finish. Engineered with precision ground carbide, these bits deliver faster starts and less walking in concrete, brick, and block. Wide flute design removes dust faster, reducing heat and delivering more holes per charge. Equipped with a 3-Flat Secure Grip™ shank, Milwaukee® Carbide Hammer Drill Bits are the ideal solution for drilling in masonry materials with hammer drills/drivers. Available in diameters up to 1 inch.
