Bussmann Bullet™ ECSR40 Current Limiting Time Delay Fuse, 40 A, 600 V, 200 kAIC Interrupt, RK5 Class, Cartridge Body
Edison's UL Class RK5 dual-element, time-delay fuses provide economical solutions to overcurrent protectioni. Available in both 250Vac and 600Vac, with 200kA RMS Sym interrupting ratings and sizes ranging from 0 to 600 amp.
-
BrandEdison
-
UPC782634508366
-
Manufacturer Part NumberECSR40
-
CountryUSA
-
Terminal TypeFerrule End
-
MaterialFiberglass
-
ClassRK5
-
Response Time10 s at 500%
-
TypeCurrent Limiting Time Delay
-
Mounting TypeHolder
-
Voltage Rating600 V
-
Amperage Rating40 A
-
SeriesECSR
-
Indicating/Non-IndicatingNon-Indicating
-
Interrupt Rating200 kAIC
-
Body Size1.06 in Dia x 5.5 in L
-
Body TypeCartridge
-
ElementDual
- Provides motor overload, ground fault and short circuit protection
- When used in circuits subject to surge currents such as those caused by motors, transformers and other inductive components, these fuses can be sized close to full load amps to give maximum overcurrent protection
- The time delay feature makes it possible to use fuse amp ratings which are much smaller than those of non-time delay fuses
- Considerable cost savings occur by permitting the use of smaller size switches, panels and fuses themselves
- Provides a higher degree of short circuit protection (greater current limitation) in circuits in which surge currents or temporary overloads occur
- Gives motor running back-up protection to motors without extra costs
- Helps protect motors against burnout from 1 ph on 3 ph systems
- Simplifies and improves blackout prevention (selective co-ordination ratios)
- Dual element fuses can be applied in circuits subject to temporary motor overloads and surge currents to provide both high performance short circuit and overload protection
- Superior overload and cycling capabilities
-
Alternative Part Number11197079
-
UNSPSC39121606
-
IDEA Index ID11197079
-
Package DescriptionEACH
-
Standards/ApprovalsCE Certified|CSA C22.2 File No.248.12 Guide JDDZ|UL File No.E162363
-
Catalog
-
Specification Sheet
Recently Viewed
Bussmann Bullet™ ECSR40 Current Limiting Time Delay Fuse, 40 A, 600 V, 200 kAIC Interrupt, RK5 Class, Cartridge Body
Edison's UL Class RK5 dual-element, time-delay fuses provide economical solutions to overcurrent protectioni. Available in both 250Vac and 600Vac, with 200kA RMS Sym interrupting ratings and sizes ranging from 0 to 600 amp.
McGill® CAGEROL® machined race needle bearings are manufactured from bearing quality steel. Most sizes use crowned or end relieved, rollers to help reduce end stresses and allows for greater misalignment. The rollers are separated by a steel retainer (cage) to help achieve higher speeds and provide a lubricant reservoir. CAGEROL® bearings are constructed with radial lubrication hole and groove on the outer and optional inner raceway (MI series) for relubrication through the housing or shaft. Other options include a variety of seal configurations to either help prevent contaminant entry or contain the lubricant.
FYH® NA211 34 NA Series Cylindrical Insert Bearing, 2-1/8 in Dia Bore, 2.81 in W, 43.4 kN Dynamic/29.4 kN Static Load
FYH® NA211 34 NA Series Cylindrical Insert Bearing, 2-1/8 in Dia Bore, 2.81 in W, 43.4 kN Dynamic/29.4 kN Static Load
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
The Crosby G-209 1/4" is a premium, high-strength screw pin anchor shackle designed for quick, temporary connections in tie-down, towing, suspension, or lifting applications. It features an industry-standard 0.5-ton (1,100 lbs) working load limit (WLL) and is instantly recognizable by Crosby's trademark Red Pin®
LUFKIN Mezurall™ W9212 Measuring Tape, 12 ft L x 1/2 in W Blade, Steel Blade, Feet and Inches to 1/16th Top Edge, Inches to 1/16th Bottom Edge, First 12 in to 1/32nds Graduation
Crescent Lufkin® Mezurall series tape measures are built with durability and comfort in mind. Featuring a compact and sturdy chrome case, these tape measures fit easily into pockets or travel bags.
