Wagner by Diversitech WG840586 Direct Drive Furnace Blower Motor, OAO Enclosure, 1/3 hp, 208/230 V AC, 60 Hz, 1 ph, 48 Frame, 1075 rpm Speed, Belly Band/Shaft Up/Down Mount
This Wagner® WG840586 Direct Drive Furnace Blower Motors, 1/3hp, 1075/3 RPM, 2.2FLA, 208-230V motor installs with all standard 48 frame mounting brackets. It is protected by an automatic overload and class B insulation. The motor is electrically reversible and features 36 in. leads to ease installation.
-
BrandWagner by Diversitech
-
Manufacturer Part NumberWG840586
-
CountryUSA
-
Temperature Rating140 deg F
-
Frame48
-
Frequency Rating60 Hz
-
Mounting TypeBelly Band/Shaft Up/Down
-
RotationReversible
-
Voltage Rating208/230 V AC
-
Amperage Rating2.9 A Full Load
-
Application TypeCondenser Fan Motors
-
Service Factor1
-
Horsepower1/3 hp
-
Shaft Size1/2 in Dia x 4-1/2 in L
-
Dimensions5.59 in Dia x 9.39 in L
-
Bearing TypeSleeve
-
Number of Speeds3
-
Insulation ClassClass B
-
Speed1075 rpm
-
Enclosure TypeOAO
-
Phase1
- Motors feature reversing plugs, extended thru bolts, 36 in leads and low power consumption
- Ball bearing design allows for greater heat endurance, improved performance, increased reliability, and enhanced motor life
- Extended mounting bolts provides easier installation in cramped spaces and allows the installer to start the threaded mounting nut quickly and efficiently
-
UNSPSC26101100
-
Package DescriptionEACH
-
Warranty2 Years
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
This Wagner® WG840586 Direct Drive Furnace Blower Motors, 1/3hp, 1075/3 RPM, 2.2FLA, 208-230V motor installs with all standard 48 frame mounting brackets. It is protected by an automatic overload and class B insulation. The motor is electrically reversible and features 36 in. leads to ease installation.
THRUST BEARING-INA902>
IKO manufactures a wide range of radial Needle Roller Bearings to meet the needs of different applications and machine profiles. These include shell type bearings, needle roller cages for both general use and within engine connecting rods and machined type Needle Roller Bearings. Shell type Needle Roller Bearings are lightweight, low profile motion components designed to handle either high speeds or heavy loads, depending on the configuration. An outer ring made of high strength steel enables a streamlined profile with the lowest sectional height of all the Needle Roller Bearings.
Browning® 1296482 T55L Automatic Torque Limiter, 1 in Finished Bore, 5-1/2 in OD, 3800 in-lb (1-Spring)/6800 in-lb (2-Spring) Torque
The Browning® torque limiter is a spring loaded friction style torque overload device. The load on the friction pads is adjusted so that the process torque is transmitted. An overload torque in excess of the set torque causes the unit to slip. This prevents overloads from transmitting through the system. When the load falls below the set level, the torque limiter stops slipping and transmits the torque. A torque limiter does not maintain phase between input and output. Although it is a similar size, the Browning® torque limiter has a higher torque density than the Morse® torque limiter. It is also well suited for applications that trip infrequently at high loads. It is most often used in a chain drive. A specially machined sprocket is inserted between the friction pads and acts as the slip interface. Torque capacity is up to 8800 in-lb.
1-1/4" X 4" M/D RECT DIE SPRINGS-LANSMDR1250400 >
Milton s976 Dual Head Tire Pressure Gauge, 10-160 PSI, Dually Tire Pressure Gauge, Truck, Tractor Trailer, RV & Car
Dual chuck head Service Gauge has a maximum pressure of 160 psi. Milton® precision engineered Service Gauges provide accurate, long life and trouble-free performance. Plated brass tube and 4 sided nylon indicator bar. 100% Calibrated across all three psi ranges before leaving the factory.
