Browning® 1296342 Automatic Torque Limiter, 3/4 in Straight Bore, 2-1/2 in OD, 800 in-lb (1 Spring)/1100 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
-
BrandBrowning®
-
UPC662289121533
-
Manufacturer Part Number1296342
-
CountryUSA
-
Maximum Speed1000 rpm
-
Torque Rating800 in-lb (1 Spring)/1100 in-lb (2 Spring)
-
TypeAutomatic
-
Minimum Sprocket Teeth25 (NO. 35 Chain), 20 (NO. 40 Chain), 20 (NO. 41 Chain)
-
Outside Diameter2-1/2 in
-
Bore Diameter3/4 in
-
Bore TypeStraight
-
Overall Length2-1/16 in
- High accuracy
- Low cost
- Compact and reversible
- Non-asbestos pads
- Model T25L
- Morse and Browning offer a complete line of Torque Overload Devices to protect machinery from overloads or jams
- Browning torque limiters slip under excessive load but automatically carry the desired load after the excess has been removed
- Stock Sprockets are available in a variety of pitches and number of teeth machined as an accessory to fit Torq/ Gard torque overload devices
- Browning torque limiters are friction type devices that reset to any position
-
Alternative Part NumberT25LX3/4
-
UNSPSC41114510
-
Package DescriptionEACH
-
Warranty1 Year
-
Instruction/Installation Manual
Recently Viewed
Browning® 1296342 Automatic Torque Limiter, 3/4 in Straight Bore, 2-1/2 in OD, 800 in-lb (1 Spring)/1100 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
RIDGID® 46205 Eye Bolt Assembly, For Use With: Model 300/300A Power Drive
RIDGID® 46205 Eye Bolt Assembly, For Use With: Model 300/300A Power Drive
The Starrett 178 Series Fillet or Radius Inch Reading Gages are very useful for tool and diemakers, machinists, screw machine operators, patternmakers and other mechanics to lay out and check radii of tools, dies, patterns, and more. 30 Leaves, 1/32-1/4" Range, 64ths increments.
Greenlee® 00930 Ultra Hole Cutter Kit, 6 Pieces, For Use With 1/2 to 2 in Conduit, HSS
Greenlee® 930 Ultra Hole Cutter Kit, 6 Pieces, For Use With 1/2 to 2 in Conduit, HSS
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
#8 X 2-1/2" Flat Head Phillips Sheet Metal Screw
