Browning® 1296391 Automatic Torque Limiter, 1 in Straight Bore, 3-1/2 in OD, 1800 in-lb (1 Spring)/3000 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
-
BrandBrowning®
-
UPC662289291670
-
Manufacturer Part Number1296391
-
CountryUSA
-
Maximum Speed1000 rpm
-
Torque Rating1800 in-lb (1 Spring)/3000 in-lb (2 Spring)
-
TypeAutomatic
-
Minimum Sprocket Teeth26 (NO. 40 Chain), 26 (NO. 41 Chain), 21 (NO. 50 Chain)
-
Outside Diameter3-1/2 in
-
Bore Diameter1 in
-
Bore TypeStraight
-
Overall Length2-1/4 in
- High accuracy
- Low cost
- Compact and reversible
- Non-asbestos pads
- Model T35L
- Morse and Browning offer a complete line of Torque Overload Devices to protect machinery from overloads or jams
- Browning torque limiters slip under excessive load but automatically carry the desired load after the excess has been removed
- Browning offers a complete set of replacement shear pins
- Shear pins are available in a wide range of minimum shear strength
- Browning torque limiters are friction type devices that reset to any position
-
Alternative Part NumberT35LX1
-
UNSPSC41114510
-
Package DescriptionEACH
-
Warranty1 Year
-
Instruction/Installation Manual
Recently Viewed
Browning® 1296391 Automatic Torque Limiter, 1 in Straight Bore, 3-1/2 in OD, 1800 in-lb (1 Spring)/3000 in-lb (2 Spring) Torque
Browning® torque limiters are torque control devices that slip under excessive load but automatically carry the desired load after the excess has been removed. The device can be easily adjusted to slip at a desired overload and automatically re-engage when overload is removed. Overload should be removed promptly since prolonged slippage can be detrimental to the friction disc. Generally, no resetting is required after the torque limiter has slipped. Torque limiters help prevent machine and product damage and costly downtime caused by shock loads, overloads or machine jams but should not be used as clutches.
12-MB-12-MB HYDRAULIC ADAPTERS-DAY64071212>
FiberFix 2 HEAT WRAP Insulative Moisture Resistant Reinforced Heat Wrap, 2 in W x 70 in L, Fiber/Resin, Black
FiberFix 2 HEAT WRAP Insulative Moisture Resistant Reinforced Heat Wrap, 2 in W x 70 in L, Fiber/Resin, Black
Flex-Hone® GBD33418 Heavy Duty Flexible Cylinder Hone, 3-3/4 in Dia Bore, 5 in L Abrasive, 13-1/2 in OAL, 180 Grit
The BRM Flex- Hone® Tool is a resilient, flexible honing tool with a soft cutting action. It's unique construction allows the abrasive globules or "stones" to float, assuring the tool will be self-centering, self-aligning to the bore and self-compensating for wear. The tool is available in a variety of different grits and sizes ranging from 4 mm to 36 in. Whether your need is cross hole deburring, surface finishing or edge blending there is a Flex- Hone® Tool designed for you. A non-directional or crosshatched pattern is created on the surface that contains valuable valleys between the plateaus for oil retention. Finer grits can assist with achieving single RA finishes. In Automotive, Hydraulic, Pneumatic or Industrial applications, the Flex- Hone® Tool will provide a superior surface finish bringing increased product performance, longer product life and less product reject.
BBI 500124 Full Thread Tap Bolt, 3/8-16, 5-1/2 in L Under Head, A Grade, Low Carbon Steel, Zinc CR+3
BBI 500124 Full Thread Tap Bolt, 3/8-16, 5-1/2 in L Under Head, A Grade, Low Carbon Steel, Zinc CR+3
Milwaukee® 6890 Double Insulated Corded Electric Nibbler, 16 ga Cold Rolled Steel, 18 ga Stainless Steel Cutting, 1-3/4 in Cutting Radius, 1900 spm, 120 V AC/DC, Metal Housing, 11-1/4 in OAL
A nibbler uses a punch and die to make the cut, this is perfect for tight radius cuts into steel. The cutter can be set in 8 positions to make cutting easier. A .87 in. starter hole is all that is needed to start or start from the edge of the material. A nibbler is also what you need if you are cutting corrugated metal. The 6890 nibbler can cut 16 gauge steel and 18 gauge stainless. When perfect cuts are what you need, look to the Milwaukee line of nibblers.
