Browning® 1305002 Stock Shear Pin, 3/16 in Dia Neck, 1-1/8 in OD, For Use With Model SHH1 Hub, 3730 in-lb Torque, Steel
Browning® shear pin hubs are designed to shear a necked pin at a predetermined load. This protects equipment from overloads. Consisting of a hub assembly, a sprocket and shear pin, the shear pin bridges between the sprocket and hub assembly. The shear pin is available in load increments, so the closest one to your application requirements must be chosen. Resetting the shear pin hub is accomplished manually by replacing the shear pin. Best applied to applications where infrequent overloads are encountered.
-
BrandBrowning®
-
UPC662289285174
-
Manufacturer Part Number1305002
-
CountryUSA
-
MaterialSteel
-
Maximum Speed100 rpm
-
Torque Rating3730 in-lb
-
Neck Diameter3/16 in
-
Horsepower5.9 hp
-
Outside Diameter1-1/8 in
-
Suitable For Use WithModel SHH1 Hub
- Helps prevent damage to machinery due to sudden overload by shearing a necked pin at the predetermined load
- Sprocket rotates freely after pin breakage, allowing the drive to idle
- Universal mounting
- Single position
- Reversibility and repeatability
- Morse and Browning offer a complete line of Torque Overload Devices to protect machinery from overloads or jams
- Browning offers a complete set of replacement shear pins
- Replacement discs are readily available at 2 per pack
- Shear pins are available in a wide range of minimum shear strength
-
Alternative Part Number4H SH PIN
-
UNSPSC31161610
-
Package DescriptionEACH
-
Warranty1 Year
-
Instruction/Installation Manual
Recently Viewed
Browning® 1305002 Stock Shear Pin, 3/16 in Dia Neck, 1-1/8 in OD, For Use With Model SHH1 Hub, 3730 in-lb Torque, Steel
Browning® shear pin hubs are designed to shear a necked pin at a predetermined load. This protects equipment from overloads. Consisting of a hub assembly, a sprocket and shear pin, the shear pin bridges between the sprocket and hub assembly. The shear pin is available in load increments, so the closest one to your application requirements must be chosen. Resetting the shear pin hub is accomplished manually by replacing the shear pin. Best applied to applications where infrequent overloads are encountered.
12 TOOTHHHN GREEN ELECTRICAL WIRE (FT)-ALE12THHNGRNSOLID >
FHP V-BELT 48."-JAS4L480 >
32-OZ " THE WORKS" DRAIN CLEANER-JWH605409 >
JACKSON SAFETY® 14812 C10 Lightweight Bump Cap, Universal, Green, HDPE, 4-Point Pinlock Suspension, ANSI Specified
Jackson Safety* C10 bump caps can help provide on the job protection your workers. They help offer protection from minor bumps and scalp lacerations (where ANSI standards are not required). These lightweight safety hats are made of molded HDPE (high density polyethylene) and feature a 4-point suspension system with an absorbent brow pad. The pinlock sizing system can accommodate head sizes 6.5 to 8.25 and the helmets can be made compatible with a face shield for additional coverage.
Browning® 767334 VPLE 100 Intermediate Duty Pillow Block Ball Bearing, 2-3/16 in Dia Bore, 6-7/16 to 7-7/16 in L Bolt Center-to-Center, 2-7/16 in Base to Bore Centerline, 8-13/16 in OAL x 4-29/32 in OAH
Browning® mounted ball bearings feature multiple housing styles, materials and configurations, an extended inner race insert bearing with ball riding nylon retainer. The insert features a rivet to prevent outer ring rotation and is available with setscrew, eccentric, or BOA concentric locking collar. The contact seal, with black oxide treated flinger provides a good balance between contaminant resistance, grease loss and friction. Depending on your preference, these bearings are available in inch and metric bore with a wide variety of cast iron, stamped steel or rubber mount housings or specific industry solutions as illustrated on the pages to follow.
