Browning® Classical Gripbelt® 1042134 AK Series Type 2 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 4.45 in OD, 4.4 in (A)/3.86 in (3L) Dia Pitch, 3/4 in W Face
Browning® Classical Gripbelt® 1042134 AK Series Type 2 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 4.45 in OD, 4.4 in (A)/3.86 in (3L) Dia Pitch, 3/4 in W Face
-
BrandBrowning®
-
UPC662289292042
-
Manufacturer Part Number1042134
-
CountryUSA
-
Face Width3/4 in
-
Bushing TypeH
-
Pitch Diameter4.4 in (A)/3.86 in (3L)
-
FinishGray Painted
-
MaterialCast Iron
-
TypeType 2
-
SeriesAK Series
-
Hub Projection19/32 in
-
Outside Diameter4.45 in
-
Bore Diameter3/8 to 1-1/2 in
-
Bore TypeSplit Taper
-
Overall Length1-1/2 in
-
Suitable For Use With4L/A and 3L Cross Section Belt
- Largest Selection of H Bushed sheaves of any other manufacturer - Browning offers bushed sheaves in both A and B Combination (A/B) configuration
- 1 and 2 Grooves are available to meet any fractional horsepower requirement
- Sheaves are Statically Balanced - All sheaves are statically balanced to assure smooth, vibration free performance
- Close Grain Cast iron - Close grain cast iron allows Browning to machine our sheaves to the closest tolerances possible
- Twice balanced after assembly
- Tightened micro-finish on groove walls for increased belt life
- Split Taper® bushings are highest torque carrying capacity in the Browning® bushing product line
- Double split barrel assures true concentricity
- Largest Selection of H Bushed sheaves of any other manufacturer - Browning offers bushed sheaves in both A and B Combination (A/B) configuration
- Sheaves are Statically Balanced - All sheaves are statically balanced to assure smooth, vibration free performance
- Combination Groove - All Browning B5V Sheaves permit the running of A, 4L, B, 5L and 5V Belts to be run in them, thus providing a variety of different pitch diameters and horsepowers
- Broad horsepower coverage - The B5V is available in 1 through 6 grooves allowing it to cover from 5 to 125 horsepower drives
- Incorporates Browning Split Taper Bushing - The only bushing system that provides a true Key-to-Key drive to both the shaft and the hub
- New Casting design - The B5V castings were developed using CAD and Finite Elements Analysis to determine where to add and eliminate material
- Close Grain Cast iron - Close grain cast iron allows Browning to machine our sheaves to the closest tolerances possible
-
Alternative Part NumberAK46H
-
UNSPSC24101610
-
Package DescriptionEACH
-
Warranty1 Year
-
Catalog
Recently Viewed
Browning® Classical Gripbelt® 1042134 AK Series Type 2 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 4.45 in OD, 4.4 in (A)/3.86 in (3L) Dia Pitch, 3/4 in W Face
Browning® Classical Gripbelt® 1042134 AK Series Type 2 Single Groove Sheave, Split Taper Bore, 3/8 to 1-1/2 in Dia Bore, 4.45 in OD, 4.4 in (A)/3.86 in (3L) Dia Pitch, 3/4 in W Face
Alemite® 1743-B Straight Drive Fitting, 35/64 in OAL, 1/4 in L Shank, Trivalent Zinc Plated
Alemite® 1743-B Straight Drive Fitting, 35/64 in OAL, 1/4 in L Shank, Trivalent Zinc Plated
The 5000® Series of bearings is similar in construction to the 400® Series bearing except it has a flange on the outer ring to locate the bearing when pressed into a tube or housing, thus eliminating the need for an external mounting device. The bearings are designed for moderate loads and speeds where running accuracy and noise level requirements do not warrant the more expensive precision ground bearings. This series of bearings feature a full ball complement without a retainer. The rings are case hardened and the soft steel band on the outer ring of the unitized assembly allows the bearing to be pressed into a housing without the necessity of close housing tolerances. The bearings are supplied pregreased as a standard. The bearings are designed for use in applications with speeds not exceeding 1200 rpm.
Dodge® Tigear-2® 26Q15L56 Standard Right Angle Worm Gear Speed Reducer, Quill Input, Solid A Shaft Output, 3.62 hp, 15:1 Gear, 117 rpm Maximum Output, 1708 in-lb Torque Rating
The speed reducer shall be a single reduction worm gear reducer incorporating three input configurations - a quill style for direct attachment of electric motors, a separate keyed input shaft suitable for flexible coupling to a footed motor or belt and pulley input configuration and a motor adapter style input that employs a three piece coupling to connect electric motors to the reducer. These input configurations shall be available in both solid and hollow output shaft designs. The reducer shall be manufactured in the United States of America.
Kuriyama ABF300 ABF Pin Lug Hose Aluminum Shank, 3 in Nominal, NPSM End Style, Import
Leviton® wire mesh safety grips are built tough to provide the strength, reliability and gripping force required for today's demanding wire management applications. They are designed to distribute stress over a large area so they can securely hold, pull or support the wire, rope, tubing or fiber optic cable to which they are applied. Leviton® wire mesh safety grips are flexible holding devices used to pull cable, rope or tubing into place, to support it after it has been installed, to prevent cable pullout or to provide strain relief that reduces the arc of bend at points of wire connections or terminations. Available in a wide selection of style, weave, attachment and wire options designed to meet the highest standards for strength, flexibility, durability and longevity.
