Browning® Gearbelt® 1057124 Type 9 Synchronous Timing Pulley With Flange, 1/2 to 1-3/4 in Split Taper Bore, 3.766 in OD, 24 Grooves, 3.82 in Dia Pitch, 1-3/4 in W Face
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
-
BrandBrowning®
-
UPC662289173983
-
Manufacturer Part Number1057124
-
CountryUSA
-
Face Width1-3/4 in
-
Bushing TypeP1
-
Pitch1/2 in
-
Pitch Diameter3.82 in
-
Flange Diameter4-1/16 in
-
TypeType 9
-
Hub Diameter3 in
-
Hub Projection5/8 in
-
Number of Grooves24
-
Outside Diameter3.766 in
-
Bore Diameter1/2 to 1-3/4 in
-
Bore TypeSplit Taper
-
Overall Length2-5/8 in
-
Suitable For Use With1-1/2 in W Type H150 Belt
- Constant Speed - No slip, no creep, minimum backlash due to the positive engagement of the belt teeth with the grooves of the sprockets
- Broad depth of product to choose from - Browning offers 5 different sprocket pitches along with a wide range of sprocket and belt widths to accommodate any horsepower requirement
- Different Mounting to the shaft - Browning offers the Gearbelt Pulleys in various ways to mount to the shaft, Split Taper and QD Bushing styles, as well as, finished and minimum plain bore
- Lightweight, high horsepower-to-weight ratio makes Gearbelt® drives ideal for any application where weight is an important factor
- Less heat, because Gearbelt® drives generate virtually no friction
- No lubrication required
- Wide load capacity range
- Constant Speed - No slip, no creep, minimum backlash due to the positive engagement of the belt teeth with the grooves of the sprockets
- Different Mounting to the shaft - Browning offers the Gearbelt Pulleys in various ways to mount to the shaft, Split Taper and QD Bushing styles, as well as, finished and minimum plain bore
- Largest Selection of H Bushed sheaves of any other manufacturer - Browning offers bushed sheaves in both A and B Combination (A/B) configuration
- Sheaves are Statically Balanced - All sheaves are statically balanced to assure smooth, vibration free performance
- Close Grain Cast iron - Close grain cast iron allows Browning to machine our sheaves to the closest tolerances possible
- Combination Groove - All Browning BK H Sheaves permit the running of A, 4L, B and 5L Belts to be run in them, thus providing a variety of different pitch diameters and horsepowers
- Broad depth of product to choose from - Browning offers 5 different sprocket pitches along with a wide range of sprocket and belt widths to accommodate any horsepower requirement
-
Alternative Part Number24HP150
-
UNSPSC26111807
-
Package DescriptionEACH
-
Warranty1 Year
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
Browning® Gearbelt® 1057124 Type 9 Synchronous Timing Pulley With Flange, 1/2 to 1-3/4 in Split Taper Bore, 3.766 in OD, 24 Grooves, 3.82 in Dia Pitch, 1-3/4 in W Face
Synchronous belt drives help reduce the problems of slippage, belt stretch, lubrication and metal to metal contact. They provide superior performance because power is transmitted by positive engagement of belt teeth rather than by friction, as in conventional belt drives.
Browning® 1076934 QD Bushing, 1-1/8 in Dia Bore, 2-3/16 in Dia Barrel, 3-1/8 in Dia Flange, 1.33 in OAL, Ductile Iron
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
Morse® AV26 Master Cobalt® Heavy Duty Hole Saw, 1-5/8 in Dia, 1-1/2 in D Cutting, M3 HSS Cutting Edge
Weiler® 08045 ST-4 Heavy-Duty Wheel Brush, 4 in Dia Brush, 1/2 in W Face, 0.014 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 1/2 to 5/8 in Arbor Hole
Weiler® 08045 ST-4 Heavy-Duty Wheel Brush, 4 in Dia Brush, 1/2 in W Face, 0.014 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 1/2 to 5/8 in Arbor Hole
Weiler® 08075 Wheel Brush, 6 in Dia Brush, 1/2 in W Face, 0.0118 in Dia Filament/Wire Standard/Twist Knot Filament/Wire, 1/2 to 5/8 in Arbor Hole
Weiler® 6 in standard twist knot wire Wheel Brush provides a heavy duty brushing action with some flexibility for demanding deburring cleaning and surface preparation applications on somewhat irregular surfaces. Featuring Weiler® individual knot hole construction, these radial brushes are available in heat treated steel, type 302 stainless steel and bronze wire for use in a wide variety of applications. 5/8 to 1/2 in arbor hole for use on bench/pedestal grinder, die grinder, right angle die grinder and straight grinders.
1/4" -FEMALE PIPE THREAD GALVANIZED TEE-FIT1/4GT >
