Gates® Power Transmission Super HC® Molded Notch PowerBand® 4/5VX1600 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 160 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
-
BrandGates® Power Transmission
-
UPC72053222012
-
Manufacturer Part Number4/5VX1600
-
CountryUSA|Canada
-
Temperature Range-60 to 250 deg F
-
Thickness35/64 in
-
MaterialEPDM
-
Top Width5/8 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeHeavy Duty Molded Notch
-
Minimum Pulley Diameter7.958 in
-
Section Size5VX
-
Series9389
-
Number of Ribs4
-
Outside Length160 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- Notches molded into the belt during manufacturing increase flexibility making this belt well suited for drives with smaller diameter sheaves
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Patented ethylene material construction provides -60 to 250 deg F temperature range to resist belt cracking
-
Alternative Part Number93894160
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Super HC® Molded Notch PowerBand® 4/5VX1600 Heavy Duty Molded Notch V-Belt, 5VX Section, 5/8 in W Top, 160 in L Outside, 35/64 in THK, EPDM
When your power transmission application needs a high horsepower solution but is constrained by drive weight or physical space, the answer is Super HC™ Molded Notch belts. Our proprietary ethylene construction process provides a superior combination of flex and load-carrying capacity, transmitting up to three times the horsepower versus comparably sized belts. Super HC MN V-belts put more power where high speeds, high speed ratios or small pulley diameters are required, offering significant benefits over classical section V-belts.
4" -MALE PIPE THREADXCLOSE BLACK NIPPLE-JPW4XCLBN >
1/4" -MALE PIPE THREADX3-1/2" GALVANIZED NIPPLE-FIT1/4X31/2GN >
Browning® Gearbelt® 3514049 Type D Arm Synchronous Timing Pulley, 1/2 to 2-15/16 in QD® Bore, 13.315 in OD, 84 Grooves, 13.369 in Dia Pitch, 1-13/16 in W Face
Browning® 1251370 Straight Type LR Bevel Gear Reducer, Shaft Input, Shaft Output, 1 hp, 1:1 Gear, 1750 rpm Maximum Output, 36.013 in-lb Input/28.82 in-lb Output Torque Rating
Browning® cast iron bevel and spiral bevel gear reducers are constructed of rugged cast iron housings. These housings are line bored for precise gear and bearing alignment. To offer maximum performance, these reducers are designed with tapered roller and ball bearings. Browning® cast iron bevel and spiral bevel gear reducers are available in six sizes and ratios. These range from 1:1 to 3:1, with speed-up ratios available. Torque capacity ranges from 99 to 5942 in-lb.
PW-57 KEROSENE HEATER REPLACEMENT WICK FIT MOST ALL HEATERS. A CROSS REFERENCE, CHART AND INSTALLATION GAUGE ENCLOSED IN EACH PACKAGE-JWH414735 >
