Gates® Power Transmission Hi-Power® II B26 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 29 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC770075425687
-
Manufacturer Part NumberB26
-
CountryUSA|Canada
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter4.775 in
-
Section SizeB
-
Series9003
-
Number of Ribs1
-
Outside Length29 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
-
Alternative Part Number90032026
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Catalog
-
Instruction/Installation Manual
Recently Viewed
Gates® Power Transmission Hi-Power® II B26 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 29 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
TRAILER JACKS-VALVI720>
Gates® Power Transmission Hi-Power® II C81 Banded Heavy Duty V-Belt, C Section, 7/8 in W Top, 85 in L Outside, 17/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Track rollers (also known as cam followers) are characterized by their thick-walled outer rings that run directly on a track. The thick outer rings permit high load-carrying capability while minimizing both distortion and bending stresses. Sealed designs with internal thrust washers help extend service life under conditions of infrequent lubrication.
JASON BX136 COGGED CLASSICAL V-BELTS. 21/32 " TOP WIDTH, 13/32 " THICK
RAW EDGE COGGED V-BELT; 21/32 WIDTH, 139" BELT OUTSIDE LENGTH, 1 BAND, POLYESTER TENSILE MATERIAL, RUBBER OUTER MATERIAL.
-JASBX136 >
BANJO B-301-GSA 3" EPDM MANIFOLD GASKET WITH RIB-REPLACEMENT PARTS
SEAL WITH THE BANJO M301G 3" EPDM MANIFOLD GASKET WITH RIB. PERMEABLE, FLEXIBLE AND WATER RESISTANT TO TIGHTLY SEAL CONNECTIONS IN MANY AGRICULTURAL APPLICATIONS. THE RIB ACTS AS A THIRD HAND HOLDING THE GASKET IN PLACE WHILE YOU TIGHTEN THE CLAMP
-BAJM301GSA >
