Torrington 5/8" CAM FOLLOWERS TOR CRS-10-1
Track rollers (also known as cam followers) are characterized by their thick-walled outer rings that run directly on a track. The thick outer rings permit high load-carrying capability while minimizing both distortion and bending stresses. Sealed designs with internal thrust washers help extend service life under conditions of infrequent lubrication.
-
BrandKoyo
-
UPC605790207105
-
Manufacturer Part NumberCRS-10-1
-
CountryUSA
-
Load Capacity1070 lbf Dynamic/1510 lbf Static
-
Temperature Rating-25 to 225 deg F
-
FinishBlack Oxide
-
Thread Length5/16 in
-
Thread Size1/4-28
-
Maximum Speed5500 rpm Grease
-
Closure TypeSealed
-
TypeStud Type Uncaged
-
Roller Diameter5/8 in
-
Roller MaterialSteel
-
Roller Width0.438 in
-
SeriesCRS Inch Series
-
Stud Diameter1/4 in
-
Stud Length3/4 in
- Screwdriver slot in head facilitates mounting
- Non-separable, sealed unit with outer ring, full complement of needle rollers, stud seals, self-lubricating resin internal thrust washers and stud-fastened retaining washer
- Seals help retain lubricant and exclude foreign matter
- Re-lubrication via axially drilled hole through stud with cross-drilled holes in stud raceway and shank
- Recessed axial hole accepts standard nominal inch drive-type grease lubrication fitting
- Lubrication fitting plugs furnished to close off unused holes
- Tolerance limits for outer diameters of stud and outer ring refer to
- A close fit between stud and hole required for mounting
- Retaining washer should be firmly backed up by flat housing shoulder (perpendicular to the stud axis)
- Shoulder diameter should be atleast same size as minimum clamping diameter listed
- May be mounted with two thin lock nuts or nut and lock washer
-
Alternative Part NumberCRS101PBL449
-
UNSPSC31171505
-
Standards/ApprovalsANSI/ABMA 18.2
-
Catalog
Recently Viewed
Track rollers (also known as cam followers) are characterized by their thick-walled outer rings that run directly on a track. The thick outer rings permit high load-carrying capability while minimizing both distortion and bending stresses. Sealed designs with internal thrust washers help extend service life under conditions of infrequent lubrication.
JASON BX136 COGGED CLASSICAL V-BELTS. 21/32 " TOP WIDTH, 13/32 " THICK
RAW EDGE COGGED V-BELT; 21/32 WIDTH, 139" BELT OUTSIDE LENGTH, 1 BAND, POLYESTER TENSILE MATERIAL, RUBBER OUTER MATERIAL.
-JASBX136 >
BANJO B-301-GSA 3" EPDM MANIFOLD GASKET WITH RIB-REPLACEMENT PARTS
SEAL WITH THE BANJO M301G 3" EPDM MANIFOLD GASKET WITH RIB. PERMEABLE, FLEXIBLE AND WATER RESISTANT TO TIGHTLY SEAL CONNECTIONS IN MANY AGRICULTURAL APPLICATIONS. THE RIB ACTS AS A THIRD HAND HOLDING THE GASKET IN PLACE WHILE YOU TIGHTEN THE CLAMP
-BAJM301GSA >
Dodge® 131434 215 Normal Duty Pillow Block Ball Bearing Unit, 2-15/16 in Dia Bore, 8-1/2 to 9-1/2 in L Bolt Center-to-Center, 3.31 in Base to Bore Centerline, 11-3/4 in OAL x 6.56 in OAH
For more than 70 years, Dodge® has been talking to mounted bearing users and listening to their needs. This experience led to design of the optimum mounted ball bearings. The result is the Dodge® SXR line, the most current eccentric collar mounted ball bearing design on the market, provides the user unmatched quality and true total value.
