Gates® Power Transmission Hi-Power® II PowerBand® 2/B62 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 65 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC72053243406
-
Manufacturer Part Number2/B62
-
CountryUSA|Canada
-
Thickness13/32 in
-
MaterialEPDM
-
Top Width21/32 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter5.73 in
-
Section SizeB
-
Series9093
-
Number of Ribs2
-
Outside Length65 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The tie band assures high lateral rigidity, guiding the belt in a straight line and preventing it from coming off the drive
- Concave sidewalls provide proper cord support and full contact with the sheave groove for equal loading and uniform wear
-
Alternative Part Number90932062
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Instruction/Installation Manual
-
Catalog
-
Specification Sheet
Recently Viewed
Gates® Power Transmission Hi-Power® II PowerBand® 2/B62 Banded Heavy Duty V-Belt, B Section, 21/32 in W Top, 65 in L Outside, 13/32 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
TCM14253SB>
OIL SEALS-2.000" X 3.251" X .437"-CHI20108>
Gates® Power Transmission PowerGrip® GT®2 Twin Power® TP2800-8MGT-50 9232 Synchronous Belt, 350 Teeth, 8 mm Pitch, 2800 mm OAL, 50 mm W, Neoprene
PowerGrip™ GT™2 Twin Power™ Belts feature dual-sided teeth to provide equal load carrying capacity on either belt surface, enabling synchronization from both driving surfaces. These synchronous belts ensure high loading capacity on contra-rotating drives and ensure smooth running and high flexibility. Gates Twin Power PowerGrip GT2 belts are designed to perform at high speeds and characterized by low-running noise, with a larger tooth profile for increased performance capacity.
TB Wood's® sheaves are constructed of fine grain, high tensile cast iron, and have been carefully engineered to assure maximum performance over a long life span. Behind each sheave is one of the most extensive engineering design and testing programs in the industry. With the advent of higher V-belt ratings, TB Wood's® engineers instituted additional careful test programs to ensure that each Wood's sheave would be capable of safely and dependably delivering the increased performance which was required by the new ratings. TB Wood's® engineers, using a special strain gage test stand, subject sheaves to tension and compression stresses far in excess of those encountered in actual operation.
Gates® Power Transmission PowerGrip® GT®2 Twin Power® TP1890-14MGT-40 9232 Synchronous Belt, 135 Teeth, 14 mm Pitch, 1890 mm OAL, 40 mm W, Neoprene
PowerGrip™ GT™2 Twin Power™ Belts feature dual-sided teeth to provide equal load carrying capacity on either belt surface, enabling synchronization from both driving surfaces. These synchronous belts ensure high loading capacity on contra-rotating drives and ensure smooth running and high flexibility. Gates Twin Power PowerGrip GT2 belts are designed to perform at high speeds and characterized by low-running noise, with a larger tooth profile for increased performance capacity.
