Gates® Power Transmission Hi-Power® II A162 Banded Heavy Duty V-Belt, A Section, 1/2 in W Top, 164 in L Outside, 5/16 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
-
BrandGates® Power Transmission
-
UPC770075267515
-
Manufacturer Part NumberA162
-
CountryUSA|Canada
-
Thickness5/16 in
-
MaterialEPDM
-
Top Width1/2 in
-
Reinforced MaterialFlex-Bonded Polyester
-
TypeBanded Heavy Duty
-
Minimum Pulley Diameter4.138 in
-
Section SizeA
-
Series9002
-
Number of Ribs1
-
Outside Length164 in
- Flex-bonded cords are strongly bonded to the body of the belt resulting in equal load distribution and the absorption of bending stress without cord deterioration
- The Flex-Weave® cover is constructed for longer cover life, providing extended protection to the core of the belt from oil, dirt and heat
- Gates® curves provide proper cord support and full contact with the sheave groove for uniform loading, uniform wear and increased belt life
- Featuring a composite, multi-purpose construction, these belts resist oil and heat, ozone, sunlight, weather and aging
-
Alternative Part Number90022162
-
UNSPSC26111801
-
Package DescriptionEACH
-
Standards/ApprovalsARPM/RMA IP-3-2/IP-3-3
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Gates® Power Transmission Hi-Power® II A162 Banded Heavy Duty V-Belt, A Section, 1/2 in W Top, 164 in L Outside, 5/16 in THK, EPDM
The wrapped classical section Hi-Power™ V-belt has a long reputation for reliability on agricultural and industrial applications. The arched top of the Hi-Power belt provides superior strength to prevent "dishing" and distortion of the tensile section. The cords are properly aligned, each of them carrying its full share of the load.
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
Sealmaster® 700394 SEHB Non-Expansion Standard-Duty Hanger Ball Bearing Unit, 1-1/4 in Dia Bore, 3-5/8 in OD, 1-11/16 in W, Cast Iron Bearing, Set Screw Collar Locking
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing and lubrication options or industry specific solutions.
2" -MALE PIPE THREADX2-1/2" GALVANIZED NIPPLE-FIT2X21/2GN >
FYH® NAPK209 26 NAPK Normal Duty Pillow Block Unit, 1-5/8 in Dia Bore, 5-7/8 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-15/32 in OAL 4-3/16 in OAH
FYH® NAPK209 26 NAPK Normal Duty Pillow Block Unit, 1-5/8 in Dia Bore, 5-7/8 in L Bolt Center-to-Center, 2-1/16 in Base to Bore Centerline, 7-15/32 in OAL 4-3/16 in OAH
