Gates® Power Transmission PowerGrip® GT®3 600-8MGT-30 Synchronous Belt, 30 mm W, 600 mm OAL, 8 mm Pitch, 75 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
-
BrandGates® Power Transmission
-
UPC770075791553
-
Manufacturer Part Number600-8MGT-30
-
CountryUSA
-
Pitch8 mm
-
MaterialNeoprene
-
Reinforced MaterialFiberglass
-
Width30 mm
-
Series9356
-
Number of Teeth75
-
Overall Length600 mm
- Fiberglass tensile cord provides high strength, excellent flex life and high resistance to elongation
- Nylon tooth facing provides a durable wear surface for long service life
- Gates® patented tooth profile is designed for use with a specific sprocket groove profile
- The sprocket groove-belt tooth combinations increases capacity, while improving registration
- Eliminates lubrication and re-tensioning to reduce maintenance and labor as compared to roller chain drives
- A single twist cord helps prevent the belt from moving downward on vertical shaft ACHE applications
- Neoprene body provides protection against grime, grease, oil and moisture
- PowerGrip® GT®3 has more tooth ratchet resistance than HTD®
-
Alternative Part Number95790010
-
UNSPSC26111811
-
Package DescriptionEACH
-
Standards/ApprovalsISO 9563
-
Specification Sheet
Recently Viewed
Gates® Power Transmission PowerGrip® GT®3 600-8MGT-30 Synchronous Belt, 30 mm W, 600 mm OAL, 8 mm Pitch, 75 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
Gates® Power Transmission PowerGrip® GT®3 600-8MGT-20 Synchronous Belt, 20 mm W, 600 mm OAL, 8 mm Pitch, 75 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
NSK R18 Deep Groove Ball Bearing, 1-1/8 in Dia Bore, 2-1/8 in OD, 1 Row, 3/8 in W, 13200 lb Dynamic/8300 lb Static Load
Deep Groove Ball Bearings (DGBB) are the most common form of rolling bearings and are used in a variety of applications, particularly those where high speeds and low power loss are required. NSK DGBB can handle not only radial forces, but also moderate axial loads in both directions. They are easy to install and can be deployed in a variety of configurations.
Gates® Power Transmission PowerGrip® GT®3 480-8MGT-50 Synchronous Belt, 50 mm W, 480 mm OAL, 8 mm Pitch, 60 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
Gates® Power Transmission PowerGrip® GT®3 375-5MGT-25 Synchronous Belt, 25 mm W, 375 mm OAL, 5 mm Pitch, 75 Teeth, Neoprene
The PowerGrip® GT®3 belt has twice the load carrying capacity of its predecessor HTD®. In addition, less width is required compared to HTD®, allowing lighter, more compact drives.
Gates® Power Transmission PowerGrip® GT®3 800-8MGT-30 Synchronous Belt, 30 mm W, 800 mm OAL, 8 mm Pitch, 100 Teeth, Neoprene
Reduce both acquisition costs and transaction costs by designing with PowerGrip® GT®3. The PowerGrip® GT®3 belt has two times the rating of competitive RPP® belts and its predecessors PowerGrip® GT® and HTD® belts. PowerGrip® GT®3 drive systems offer the largest selection of belts and sprockets in the industry. At reduced widths, PowerGrip® GT®3 belts can be used as a direct replacement for most 8 mm and 14 mm pitch standard rubber RPP® and HTD® synchronous belts.
