ASP-622-S Industry Standard Clamping Collar, 2-Piece Construction, 5/8 in ID x 1-5/16 in OD x 7/16 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630709
-
Manufacturer Part NumberG2SC-062-SS
-
CountryUSA
-
FinishPlain
-
MaterialStainless Steel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size10-32 UN-3A x 1/2 in
-
Width7/16 in
-
SeriesG2SC
-
Inside Diameter5/8 in
-
Outside Diameter1-5/16 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A582|ASTM F837 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-622-S Industry Standard Clamping Collar, 2-Piece Construction, 5/8 in ID x 1-5/16 in OD x 7/16 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
1-1/2" STAINLESS STEEL 90 DEGREE WELD ELBOW-FIT11/2SSEWELD >
Shaft support blocks are used for end or intermittent support where loads are light and deflection between supports is not a problem. Unlike shaft support rails, blocks do not permit longitudinal passage of open-type Ball Bushing® bearings. Type SB shaft support blocks enable clamping of shafts and eliminate the need for bolts, to maintain shaft position. Shimming is suggested for high-precision applications to eliminate the effect of variations in surface of base or manufacturing tolerances between supports.
MORSE® 58032 5944 Center Cutting Regular Length Single End End Mill, 1/2 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 1/2 in Dia Shank, 3 in OAL, Bright
Browning® 1045517 VP Series Type 2 Variable Pitch Sheave, 1-1/8 in Finished Bore, 5.35 in OD, 1 Groove, 3.9 to 4.7 in (3L)/4.2 to 5.2 in (A/4L)/4.4 to 5.4 in (B/5L) Dia Pitch, 3/4 to 1-1/8 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
United Abrasives-SAIT Saitlam F™ 73980 Close High Performance Coated Abrasive Flap Disc, 4-1/2 in Dia, 7/8 in Center Hole, 80 Grit, Medium Grade, Zirconia Alumina Abrasive, Type 29 Conical Disc
