ASP-300-2-S Industry Standard Clamping Collar, 2-Piece Construction, 3 in ID x 4-1/4 in OD x 7/8 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630945
-
Manufacturer Part NumberG2SC-300-B
-
CountryUSA
-
FinishBlack Oxide
-
MaterialSteel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size3/8-24 UN-3A x 1 in
-
Width7/8 in
-
SeriesG2SC
-
Inside Diameter3 in
-
Outside Diameter4-1/4 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A108|ASTM A574 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-300-2-S Industry Standard Clamping Collar, 2-Piece Construction, 3 in ID x 4-1/4 in OD x 7/8 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Browning® 3750197 Taper Bore Bushing, 1-13/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3750197 Taper Bore Bushing, 1-13/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL
Browning® 3749900 Taper Lock Bushing, 1-9/16 in Dia Bore, 3-3/8 in Dia Barrel, 2-1/2 in OAL, Steel
Browning® 3749900 Taper Lock Bushing, 1-9/16 in Dia Bore, 3-3/8 in Dia Barrel, 2-1/2 in OAL, Steel
Crosby® 1031939 HG-227-1/2X6 Turnbuckle, Jaw/Eye, 1/2 in Thread, 2200 lb Working, 6 in Take Up, 14.48 in L Close, Steel
Crosby® 1031939 HG-227 Turnbuckle, Jaw/Eye, 1/2 in Thread, 2200 lb Working, 6 in Take Up, 14.48 in L Close, Steel
Drillco 76A112C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 3/16 in Dia Cutter, 5/8 in Length of Cut, 2 Flutes, 3/16 in Dia Shank, 2-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
28" X 36" TYVEK BIB-STYLE APRON - CHR14470 >
