ASP-752-S Industry Standard Clamping Collar, 2-Piece Construction, 3/4 in ID x 1-1/2 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
-
BrandClimax
-
UPC044861630754
-
Manufacturer Part NumberG2SC-075-B
-
CountryUSA
-
FinishBlack Oxide
-
MaterialSteel
-
TypeIndustry Standard
-
Construction2-Piece
-
Screw Size1/4-28 UN-3A x 5/8 in
-
Width1/2 in
-
SeriesG2SC
-
Inside Diameter3/4 in
-
Outside Diameter1-1/2 in
- Easily installed where major disassembly would otherwise be required
- Greater axial holding power than setscrew or 1-piece clamping collars
- Effective on hard and soft shafts
- Without recessed screw
- Design fully engages the shaft without marring
-
UNSPSC31162811
-
Package DescriptionEACH
-
Standards/ApprovalsASTM A108|ASTM A574 Cap Screw
-
Specification Sheet
-
Line Drawing
Recently Viewed
ASP-752-S Industry Standard Clamping Collar, 2-Piece Construction, 3/4 in ID x 1-1/2 in OD x 1/2 in W, Steel
Black Oxide Plated Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
NIBCO 205-015 Nipple, 1/2 in x 1-1/2 in L Thread, PVC, SCH 80/XH, Domestic
NIBCO 205-015 Nipple, 1/2 in x 1-1/2 in L Thread, PVC, SCH 80/XH, Domestic
Browning® 3750593 Taper Bore Bushing, 2-5/16 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL
Dichtomatik N70131 O-Ring, 131 Dash Number, 1.674 in ID x 1.88 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 131
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
MORSE® 45067 4614 Center Cutting Medium/Long Length Roughing End Mill, 1-1/4 in Dia Cutter, 4 in Length of Cut, 6 Flutes, 1-1/4 in Dia Shank, 6-1/2 in OAL, Bright
