IKO IRB1012 Inch Series Inner Ring, 5/8 in ID x 7/8 in OD, 19.43 mm OAW, For Use With BA1412Z/BHA1412Z and YB1412 Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
-
BrandIKO
-
Manufacturer Part NumberIRB1012
-
CountryUSA
-
MaterialHigh Carbon Steel
-
Inside Diameter5/8 in
-
Bore TypeTapered
- Without oil hole
-
UNSPSC31171547
-
Catalog
Recently Viewed
IKO IRB1012 Inch Series Inner Ring, 5/8 in ID x 7/8 in OD, 19.43 mm OAW, For Use With BA1412Z/BHA1412Z and YB1412 Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
Hougen® Rotabroach® 12217 12000 Annular Cutter, 17/32 in Dia Cutter, 2 in D Cutting, M2 HSS, Bright, Weldon with 2-Flat Shank
Hougen "12000 Series" cutters were the original annular cutters invented over 35 years ago. With the most features of any annular cutter, "12000 Series" cutters provide the best performance in the largest variety of materials. Compared to traditional tooling (twist drills, etc.) "12000 Series" cutters can multiply your cutting speed by up to 3 times. And you get longer tool life, a more accurate hole, a better finish, with no burrs. Hougen cutters maximize feed rates because up to 10 cutting edges distribute the cutting load evenly. "12000 Series" cutters convert a smaller area to chips, requiring less horsepower and thrust.
3" X 1/16" X 3/8" CUTOFF WHEEL-PEACW0310T >
Champion CT5-PILOT Carbide Tipped Carbide Tipped Hole Cutter Pilot Drill Bit, 3/16 in D Cutting, High Speed Steel
Champion CT5-PILOT Carbide Tipped Carbide Tipped Hole Cutter Pilot Drill Bit, 3/16 in D Cutting, High Speed Steel
Incandescent lamps are still commonly used in homes and businesses and with our wide selection, we have enough shapes, wattages and finishes to fit almost every application and need. Many of our incandescent lamps are also available in an extended life, 130 VAC version, with even more environmentally friendly alternatives coming soon.
