MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
-
BrandMAK-A-KEY
-
Manufacturer Part NumberSK06-2
-
CountryUSA
-
FinishZinc Clear
-
MaterialCarbon Steel
-
TypeType 2 Imperial
-
Base Height3/16 in
-
Base Width3/8 in
-
Step Height1/8 in
-
Step Width1/4 in
-
Length1 ft
-
StyleStep
- Step key stock is used when worn or damaged key ways have been repaired
-
UNSPSC31163208
-
Package Description1/PK
-
Standards/ApprovalsRoHS Compliant|PROP65: This product can potentially expose you to chemicals including lead, nickel and chromium which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
-
Catalog
Recently Viewed
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
MAK-A-KEY SK06-2 Type 2 Imperial Step Keystock, 3/16 in H x 3/8 in W Base, 1/8 in H x 1/4 in W Step, Carbon Steel
IKO IRB2424 Inch Series Inner Ring, 1-1/2 in ID x 1-3/4 in OD, 38.48 mm OAW, For Use With BA2824Z and BHA2824Z Shell Type Needle Roller Bearing, High Carbon Steel
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. These rings are designed to provide a durable surface for shell-type needle roller bearings with non-machined raceways in-type IRB series shaft diameters range from 5/16 to 2-1/2 in.
FYH® SA206 20FP7 SA Series Narrow Inner Ring Bearing Pillow Block Unit, 1-1/4 in Dia Bore, 1.18 in W, 19.5 kN Dynamic/11.3 kN Static Load
FYH® SA206 20FP7 SA Series Narrow Inner Ring Bearing Pillow Block Unit, 1-1/4 in Dia Bore, 1.18 in W, 19.5 kN Dynamic/11.3 kN Static Load
Sealmaster® gold ER bearings feature a cylindrical OD and snap ring for easy installation in a roll assembly. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction.
O-rings are endless, ring shaped sealing elements with a circular cross-section that are manufactured from elastomer materials or PTFE. The designation of an O-ring is derived from the dimensions of its inner diameter and cord width in millimeters, along with the name of the material and its Shore A hardness.
Hyde® 05410 Light Duty Putty Knife, 3 in W, Steel Blade
