BrassCraft® G2R10X C1 1/4 Turn Water Supply Stop, 3/8 in Nominal, FNPT x Compression, 125 psi, Brass Body, Polished Chrome, Domestic
BrassCraft 3/8 in FIP Inlet x 3/8 in OD Compression Outlet 1/4-Turn Straight Valve controls water flow to household plumbing fixtures – faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a 90 degree turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without shutting off the water to the entire home.
-
BrandBrassCraft®
-
UPC026613137803
-
Manufacturer Part NumberG2R10X C1
-
CountryUSA
-
Temperature Rating40 to 140 deg F
-
FinishPolished Chrome
-
Pressure Rating125 psi
-
Type1/4 Turn
-
Nominal Size3/8 in
-
Domestic/ImportDomestic
-
Body MaterialBrass
-
End StyleFNPT x Compression
- For use in potable water distribution systems
- Smooth, quarter-turn operation, on/off flow control with a 90 degree turn of the handle
- Easy-to-remove handle protects against accidental operation during rough-ins
-
UNSPSC40141700
-
Package Description20/CTN
-
Standards/ApprovalsASME A112.18.1|CSA B125.1|IAPMO Listed|UPC Listed
-
Specification Sheet
-
Instruction/Installation Manual
Recently Viewed
BrassCraft® G2R10X C1 1/4 Turn Water Supply Stop, 3/8 in Nominal, FNPT x Compression, 125 psi, Brass Body, Polished Chrome, Domestic
BrassCraft 3/8 in FIP Inlet x 3/8 in OD Compression Outlet 1/4-Turn Straight Valve controls water flow to household plumbing fixtures – faucets, toilets, dishwashers, icemakers, washing machines, etc. The straight valve is most often used where the water pipe enters the room from the floor. With a 90 degree turn of the valve handle, you are able to stop the flow of water leading to the plumbing fixture, allowing for maintenance and repair without shutting off the water to the entire home.
Browning® 3750650 Taper Lock Bushing, 2-3/4 in Dia Bore, 4-1/4 in Dia Barrel, 3 in OAL, Steel
BRUSH RESEARCH BC3/4320SC BC Series Small Diameter Standard Duty Flexible Cylinder Hone, 3/4 in Dia Bore, 2-1/2 in L Abrasive, 8 in OAL, 320 Grit
The BC Series Flex-Hone® tool is designed for use on any type or size of cylinder from 4 mm up to 3 in Dia. This cylinder hone is designed for surface finishing and cross hole deburring in brake cylinders, wheel cylinders, hydraulics, pneumatics and valve guides.
ASP-622-S Industry Standard Clamping Collar, 2-Piece Construction, 5/8 in ID x 1-5/16 in OD x 7/16 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
Power Team® P159 P-Series 2-Speed Manual Hydraulic Hand Pump, 152 cu-in Tank
Power Team® hand pumps, with the angled fill port, have a built in relief valve protection system. This system is designed to protect over pressurization of the reservoir from sudden back pressure. This system also works as a seal to prevent oil leaks.
