Dixon® WB3 King Cable™ Hose Cable, 3/16 in, 28 in L, 200 psi, Carbon Steel, Domestic
Dixon® WB3 King Cable™ Hose Cable, 3/16 in, 28 in L, 200 psi, Carbon Steel, Domestic
-
BrandDixon®
-
Manufacturer Part NumberWB3
-
CountryUSA
-
FinishGalvanized
-
MaterialCarbon Steel
-
Nominal Size3/16 in
-
SeriesKing Cable™
-
Working Pressure200 psi
-
Domestic/ImportDomestic
-
Length28 in
- King cable is the low cost answer to eliminate injuries caused by broken air hose connection
- King safety cable reaches across the hose fittings to provide standby safety for hose
- Spring-loaded loops in the cable ends open easily to pass over the couplings for a firm grip on the hose
- Thoroughly tested with years of service, a positive safeguard for air hose connection - helps you meet today's safety standards
- Highly resistant to rust and corrosion
- Galvanized carbon steel wire rope
- Aluminum ferrule
- Galvanized carbon steel spring
- 1/2 - 2 in ID hose
- Cables are shipped with safety restraint labels attached
- King safety cable must be installed in the extended position (no slack)
- The Canada occupational safety and health regulations part XIII, 13:6b states: "Where an air hose is connected to a portable air powered tool used by an employee, a restraining device shall be attached to all hose connections, in order to prevent injury to an employee in the even of an accidental disconnection of a hose"
- Warning: this product contains a chemical known to the State of California to cause birth defects or other reproductive harm
- Do not use in connection with drinking water
- Wash hands after handling
-
UNSPSC40141734
-
Package Description50/BX
-
Specification Sheet
-
Catalog
Recently Viewed
Dixon® WB3 King Cable™ Hose Cable, 3/16 in, 28 in L, 200 psi, Carbon Steel, Domestic
Dixon® WB3 King Cable™ Hose Cable, 3/16 in, 28 in L, 200 psi, Carbon Steel, Domestic
22-OZ TRIGGER SPRAY STAIN REMOVER-JWH648868>
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
Klein® D327-51/2C Electronic Slim Long Nose Plier, Smooth Steel Jaw, 1.688 in L x 1/2 in W Jaw, 5-5/8 in OAL, 1/16 in W Tip
These slim long-nose pliers are great for extremely close-quarter work. The longer nose and handles provide a deeper reach. The polished inside jaws help prevent nicking of wires and are spring-loaded for self-opening.
1-1/2" -FEMALE PIPE THREAD METAL GALVANIZED CROSSES-FIT11/2GCRO >
Dodge® 004072 Babbitted Rigid Pillow Block Plain Sleeve Bearing, 2-7/16 in Dia Bore, 7-3/4 to 8-1/4 in L Bolt Center-to-Center, 2-1/8 in Base to Bore Centerline, 10-1/4 in OAL x 4-1/4 in OAH
Dodge® 004072 Babbitted Rigid Pillow Block Plain Sleeve Bearing, 2-7/16 in Dia Bore, 7-3/4 to 8-1/4 in L Bolt Center-to-Center, 2-1/8 in Base to Bore Centerline, 10-1/4 in OAL x 4-1/4 in OAH
