Dixon® WB1 King Cable™ Hose Cable, 1/8 in, 20-1/4 in L, 200 psi, Carbon Steel, Domestic
Dixon® WB1 King Cable™ Hose Cable, 1/8 in, 20-1/4 in L, 200 psi, Carbon Steel, Domestic
-
BrandDixon®
-
Manufacturer Part NumberWB1
-
CountryUSA
-
FinishGalvanized
-
MaterialCarbon Steel
-
Nominal Size1/8 in
-
SeriesKing Cable™
-
Working Pressure200 psi
-
Domestic/ImportDomestic
-
Length20-1/4 in
- King cable is the low cost answer to eliminate injuries caused by broken air hose connection
- King safety cable reaches across the hose fittings to provide standby safety for hose
- Spring-loaded loops in the cable ends open easily to pass over the couplings for a firm grip on the hose
- Thoroughly tested with years of service, a positive safeguard for air hose connection - helps you meet today's safety standards
- Highly resistant to rust and corrosion
- Galvanized carbon steel wire rope
- Aluminum ferrule
- Galvanized carbon steel spring
- 1/2 - 1-1/4 in ID hose
- Cables are shipped with safety restraint labels attached
- King safety cable must be installed in the extended position (no slack)
- The Canada occupational safety and health regulations part XIII, 13:6b states: "Where an air hose is connected to a portable air powered tool used by an employee, a restraining device shall be attached to all hose connections, in order to prevent injury to an employee in the even of an accidental disconnection of a hose"
- Warning: this product contains a chemical known to the State of California to cause birth defects or other reproductive harm
- Do not use in connection with drinking water
- Wash hands after handling
| Competitor Name | Competitor Part Number |
|---|---|
| Ferguson | DWB1 |
-
UNSPSC40141734
-
Package Description100/BX
-
Specification Sheet
-
Catalog
Recently Viewed
Dixon® WB1 King Cable™ Hose Cable, 1/8 in, 20-1/4 in L, 200 psi, Carbon Steel, Domestic
Dixon® WB1 King Cable™ Hose Cable, 1/8 in, 20-1/4 in L, 200 psi, Carbon Steel, Domestic
Sure-Grip® quick detachable bushings are easy to install and remove. Split-through flange and taper provide a true clamp on the shaft that is equivalent to a shrink fit. All sizes except JA and QT have a set screw over the key to help maintain the bushing's position on the shaft until the cap screws are securely tightened. Versatile Sure-Grip® bushings permit the mounting of the same mating part on shafts of different diameters and the mounting of different sheaves on the same shaft using the same bushing.
Weiler® 16973 Small Diameter Wheel Brush, 3 in Dia Brush, 5/8 in W Face, 0.014 in Dia Crimped Filament/Wire, 3/8 to 1/2 in Arbor Hole
Weiler® 16973 Small Diameter Wheel Brush, 3 in Dia Brush, 5/8 in W Face, 0.014 in Dia Crimped Filament/Wire, 1/2 to 3/8 in Arbor Hole
Weiler® 17906 Concave Wheel Brush, 2 in Dia Brush, 0.008 in Dia Crimped Filament/Wire
Weiler® 17906 Concave Wheel Brush, 2 in Dia Brush, 0.008 in Dia Crimped Filament/Wire
Milwaukee® 9075-20 Impact Wrench, 3/4 in Square Drive, 2500 bpm, 380 ft-lb Torque, 120 V AC/DC, 11-5/8 in OAL
Delivering a whopping 380 ft. lbs of torque and weighing only 7.2 lbs., this tool has a fantastic power to weight ratio. The 3/4 in. square anvil is more resistant to long term fatigue than a 1/2 in. anvil. The powerful 7.0 amp motor drives a unique impact mechanism at 1750 RPM (no load). This model features a friction ring and through hole socket retention, and a rocker switch for quick selection of forward or reverse. The ergonomically shaped handle with a soft cushioned grip provides a well-balanced and controllable feel to the tool. The special mechanism achieves desired installation torque faster and loosens rusted or fretted bolts in less time. This Milwaukee square drive impact wrench was designed to maximize your productivity and reduce downtime with frequent accessory changes.
1-1-1/16" PILLOW BLOCK UNIT-DOD044643 >
