Crosby® 1018455, G-209-1/2, Anchor Shackle, 2 ton Load, 1/2 in, 0.63 in Dia Screw Pin, Hot Dipped Galvanized
Crosby® 1018455 Anchor Shackle, 2 ton Load, 1/2 in, 0.63 in Dia Screw Pin, Hot Dipped Galvanized
-
BrandCrosby®
-
Manufacturer Part Number1018455
-
CountryUSA
-
Load Capacity2 ton
-
FinishHot Dipped Galvanized
-
SeriesG-209
-
Inner Length1-7/8 in
-
Inner Width1-5/16 in
-
Size1/2 in
-
Opening Size0.81 in
-
Body MaterialCarbon Steel
-
Overall Length3.28 in
-
Overall Width2.69 in
-
Eye Outer Size1.19 in
-
Pin Diameter0.63 in
-
Pin MaterialAlloy
-
Pin TypeScrew
- Working load limit and grade 6 permanently shown on every shackle
- Shackles can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds or other certification
- Approved for use at -40 to 400 deg F
- 3.25 ton through 25 ton G209 anchor shackles are type approved to DNV certification notes 2.7-1- offshore containers
- The shackles are statistical proof and impact tested to 42 J min average at -4 deg F
- The tests are conducted by Crosby® and 3.1 test certified
- All other 209 shackles can meet charpy requirements of 42 J average at -4 deg F upon special request
- Look for the Red Pin® the mark of genuine Crosby® quality
| Competitor Name | Cross-Reference Number |
|---|---|
| Grainger | 29WP63 |
-
UNSPSC24101641
-
Standards/ApprovalsABS/DNV/Lloyds/CE Certified|ASME B30.26|ABS 2007 Steel Vessel Rule 1-11-17.7|DNV Certification Notes 2.7-1|Federal Spec RR-C-271F|Type IVA|Grade A|Class 2
-
Catalog
Recently Viewed
Crosby® 1018455, G-209-1/2, Anchor Shackle, 2 ton Load, 1/2 in, 0.63 in Dia Screw Pin, Hot Dipped Galvanized
Crosby® 1018455 Anchor Shackle, 2 ton Load, 1/2 in, 0.63 in Dia Screw Pin, Hot Dipped Galvanized
1-5/8"-ID SPH/OD INSERT BEARINGS-MBUVS226>
GENERAL BEARING-GENBPF618>
BBI 898433 Wood Screw, #10, 1 in OAL, Flat Head, Slotted Drive, Zinc CR+3
Milwaukee® 49-59-2163 Annular Cutter, 1-5/8 in Dia Cutter, 2 in D Cutting, HSS, Oxide Treated, Weldon Shank
Milwaukee high speed steel annular cutters offer a thin-wall construction with an advanced tooth geometry that cuts and cleans while drilling, leading to faster holes and longer life. The cutters displace less material for the same size hole as the competition, giving you fast, burr-free holes in anything from sheet metal to thick plate steel. All Milwaukee high speed steel annular cutters have a 3/4 in. Weldon shank for use with most small magnetic drill presses and large magnetic drill presses with the correct arbor.
Drillco 73A128C 7300 Center Cutting Imperial Regular Length Single End Finishing End Mill, 7/16 in Dia Cutter, 1 in Length of Cut, 4 Flutes, 7/16 in Dia Shank, 2-3/4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
