Thomson 3/4"-ID S/S LINEAR BALL BEARINGS THP A-122026-SS
Precision Steel Ball Bushing® bearings offer great improvements in efficiency, productivity and accuracy over high-friction plain bearings flat-ways. The all-steel design makes the bearing product line perfect for replacing plain bearings in high temperature applications. Rigid construction makes them very durable compared to ball bushing bearings with polymer components. When installed in a standard Thomson® pillow block, the Precision Steel Ball Bushing® bearing can self-align up to 3 deg in all directions.
-
BrandThomson®
-
UPC662486100287
-
Manufacturer Part NumberA122026SS
-
CountryUSA
-
Load Capacity200 lb Dynamic
-
Temperature Rating600 deg F
-
TypeClosed
-
Shaft Diameter3/4 in
-
Bearing MaterialSteel
-
Outside Diameter1-1/4 in
-
Length1-5/8 in
- The RoundRail™ advantage which minimizes installation time and cost
- Steady state travel speeds up to 10 ft/s and accelerations to 450 ft/sq-s without the use of derating factors
- An operating temperature up to 600 deg F/315 deg C
- Replace high-friction plain bearings
- Lasting precision alignment
- High travel speeds
- Ease of installation
- Protection from contamination
- Precision steel Ball Bushing® bearings offer great improvements in efficiency, productivity and accuracy over high friction plain bearings flat-ways
- The all steel design makes the bearing product line perfect for replacing plain bearings in high temperature applications
- The steel sleeve anti-friction recirculating ball bushing provides rigid low drag movement 100x lower drag coefficient than a plain contact bearing
- A coefficient of friction as low as 0.001 when replacing high friction plain bearings, Precision Steel Ball Bushing® bearings dramatically improve machine productivity and efficiency
- For class S shafting
- Stainless steel ball
- Not self-aligning
-
UNSPSC31171506
-
Package Description1/PK
-
Catalog
Recently Viewed
Precision Steel Ball Bushing® bearings offer great improvements in efficiency, productivity and accuracy over high-friction plain bearings flat-ways. The all-steel design makes the bearing product line perfect for replacing plain bearings in high temperature applications. Rigid construction makes them very durable compared to ball bushing bearings with polymer components. When installed in a standard Thomson® pillow block, the Precision Steel Ball Bushing® bearing can self-align up to 3 deg in all directions.
Even the toughest of the tough will enjoy Sqwincher Sqweeze Pops. This 3 oz. Electrolyte-replenishing freezer pops come in variety of five (5) great tasting flavors with just the right amount of performance boosting electrolytes. Sqweeze pops are perfect for on-the-go hydration at locations where water isn't readily accessible. Sqwincher Sqweeze also comes in ZERO flavors for those looking for a no sugar, low calorie pick me up.
1/2" COPPER COUPLING WITH STOP-ELK1001/2 >
1-OZEX TERIOR YELLOW PAINT COLORANT-BLPAXN >
United Abrasives-SAIT Saitech Ultimate Performance™ 22084 High Performance Depressed Center Wheel, 7 in Dia x 3/32 in THK, 7/8 in Center Hole, Ceramic Alumina Oxide Abrasive
Streamline® D 06050P Refrigeration Tubing, 3/8 in OD x 50 ft L, Coil, 0.32 in Thk Wall, Copper, Domestic
Streamline® Copper Tube provides the strength, precision and cleanliness needed for the demanding conditions of HVAC and refrigeration applications. Preferred throughout the industry, our products have set the benchmark for HVACR copper tube. Streamline® Nitrogenized® ACR Copper Tube is pressurized with nitrogen to provide maximum protection against the formation of harmful oxides normally formed during brazing operations. Reduction of these oxides greatly reduces system contamination. Streamline® Refrigeration Service Tube is of a consistent dead soft temper, bright, thoroughly dried/dehydrated and packed in shrink wrapping plus individual cartons for the highest level of protection.
