Proto Tools 30-MM X 32-MM OFFSET BOX WRENCHES PRO J-1079-M
Proto® TorquePlus™ J1079M Box End Wrench, 30 x 32 mm Wrench, 12 Points, 7.5 deg Offset, 17 in OAL, Alloy Steel, Full Polished, ASME B107.100, AS954E S3.8.1
-
BrandProto®
-
UPC662679062279
-
Manufacturer Part NumberJ1079M
-
CountryUSA|Canada
-
Finish/CoatingFull Polished
-
MaterialAlloy Steel
-
Measurement SystemMetric
-
Wrench Opening30 x 32 mm
-
Wrench TypeDouble End, Offset
-
Number of Points12
-
Specifications MetASME B107.100, AS954E S3.8.1
-
Offset Angle7.5 deg
-
Overall Length17 in
-
Box End Thickness43/64 x 23/32 in
-
Box End Width45.3 x 42.6 mm
- Full polish finish provides corrosion resistance and easy-to-clean surfaces
- 12 point box end allow for fine indexing, helping to improve speed and access
- Offset box end allows access to recessed fasteners and keeps hands clear of obstructions
- Box ends incorporate the TorquePlus™ system
- Adjust adjustable wrenches tightly
- Use safety goggles, serious eye injury is possible
- Pull the wrench toward you, do not push
- Strike striking/slugging wrenches squarely
- Use correct size wrenches
- Use the type of wrench that fits the job
- Use a box type wrench if possible
- Maintain your balance
- Use a commercial lubricant on a corroded fastener
| Competitor Name | Competitor Part Number |
|---|---|
| Grainger | 4JV74 |
| Grainger | 4JV74 |
| Grainger | 4JV74 |
-
UNSPSC27111705
-
Package DescriptionEACH
-
Standards/ApprovalsAS954E S3.8.1
Recently Viewed
Proto® TorquePlus™ J1079M Box End Wrench, 30 x 32 mm Wrench, 12 Points, 7.5 deg Offset, 17 in OAL, Alloy Steel, Full Polished, ASME B107.100, AS954E S3.8.1
5/8" LSE SPRING SNAPS-NTL222752 >
M-4-7/8 4-7/8"-ID QD M-style Bushing
4-7/8"-ID QD M-STYLE BUSHING - IDCM47/8>
3/8" X 3-1/2" Split Roll Pins
Browning® finished bore sprockets are offered in single strands. Offerings include 35 to 100 pitch range. Finished bore sprockets are available from 3/8 to 2-7/16 in. Hardened teeth are available up to 30 teeth.
Justrite® 08300 Horizontal Drum Vent, 2 in NPT/NPS Bung, For Use With 205 L Petroleum Based Solvent Drums, Brass, Brass
Automatic pressure relief ensures safe workplace. No more worrying about pressure building up in your drums. These safety drum vents automatically relieve pressure between 3 and 8 psi (30 to 55 kPa). Vents are tested to allow 61 cubic inch (1-L) of water through a 3/8-in (9.5-mm) pipe nipple in less than 6 seconds. Keep the vent in closed position to prevent flammable vapor from escaping. A built-in flame arrester helps absorb and dissipate heat for added safety. Vacuum relief is automatic on vertically installed vents and manual on horizontally installed vents. Drum vents are FM Approved. For protection and avoidance of high-pressure drum failure while dispelling heat using its flame arrestor.
