Williams® JHW7039B SUPERTORQUE® Double Headed Box End Wrench, 1-1/4 x 1-5/16 in Wrench, 12 Points, 10 deg Offset, 17-5/8 in OAL, Satin Chrome
Williams® JHW7039B SUPERTORQUE® Double Headed Box End Wrench, 1-1/4 x 1-5/16 in Wrench, 12 Points, 10 deg Offset, 17-5/8 in OAL, Satin Chrome
-
BrandWilliams®
-
UPC662459103383
-
Manufacturer Part NumberJHW7039B
-
CountryUSA|Canada
-
Finish/CoatingSatin Chrome
-
Measurement SystemImperial
-
TypeDouble Headed
-
Handle TypeFlat
-
SeriesSUPERTORQUE®
-
Wrench Opening1-1/4 x 1-5/16 in
-
Wrench TypeOffset
-
Number of Points12
-
Offset Angle10 deg
-
Overall Length17-5/8 in
-
Box End Thickness23/32 x 3/4 in
-
Box End Width1-25/32 x 1-27/32 in
- SuperTorque box opening design allows application of higher torque without rounding or deforming hex fastener points
- No contact is made at the corners
- Instead, wrenching forces are placed on the flat surfaces behind the points
- Sizes are clearly marked on handle ends
| Competitor Name | Cross-Reference Number |
|---|---|
| Fastenal | 921060108 |
-
Alternative Part Number7039B
-
UNSPSC27111705
-
Standards/ApprovalsFed Spec ANSI B107.6|CSA Approved
-
WarrantyLimited
-
Catalog
Recently Viewed
Williams® JHW7039B SUPERTORQUE® Double Headed Box End Wrench, 1-1/4 x 1-5/16 in Wrench, 12 Points, 10 deg Offset, 17-5/8 in OAL, Satin Chrome
Williams® JHW7039B SUPERTORQUE® Double Headed Box End Wrench, 1-1/4 x 1-5/16 in Wrench, 12 Points, 10 deg Offset, 17-5/8 in OAL, Satin Chrome
Lift-All® EE1000X26 EE Eye and Eye Sling, 26 ft L, 90000 lb, Polyester, Black
Milwaukee® 49-57-2370 Heavy Duty Annular Cutter, 2-3/8 in Dia Cutter, 2 in D Cutting, Uncoated, Threaded Shank
Drill holes up to 3X faster than twist drill bits with the Milwaukee® 2-3/4 in. threaded Steel Hawg® cutter. This long-lasting cutter features Carbide teeth and an alternating cutting pattern to cut up to a 2 in. hole depth in steel, stainless steel, cast iron or aluminum. The spring-loaded, self-ejecting pin lets you make smoother, more accurate cuts and eject the plug faster. The Steel Hawg cutter works with most electromagnetic drill presses. Use it with arbor 49-57-0030 on Milwaukee's 4262-1 magnetic drill press or arbor 49-57-0010 on Milwaukee's 4292-1 mag press. The 2-3/4 in. bit diameter has a metric thread size of M18 x 1.5 in. shank. Use the threaded Steel Hawg with a No. 3 Morse taper arbor assembly 49 to 57 - 0010.
5-5/8" CABINET DOOR/DRAWER PULLS-JWH224260>
Ambore™ 12090 1384 Heavy Duty Jobber Length Drill Bit, 1/2 in Drill - Fraction, 0.5 in Drill - Decimal Inch, 135 deg Point, HSS, Black/Gold Oxide
MORSE® 17129 2340 1-Stage Type J Heavy Duty Jobber Length Aircraft Drill, #36 Drill - Wire, 0.1065 in Drill - Decimal Inch, 135 deg Point, Cobalt
