Browning® 1212075 Minimum Plain Bore Type 4 Spur Gear, 10 Diametral Pitch, 14.5 deg Pressure Angle, 1 in W Face, 55 Teeth, 5-1/2 in Dia Pitch, 7/8 to 1-9/16 in Dia Bore, Cast Iron
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
-
BrandBrowning®
-
UPC662289223367
-
Manufacturer Part Number1212075
-
CountryUSA
-
Face Width1 in
-
Pitch Diameter5-1/2 in
-
MaterialCast Iron
-
Pressure Angle14.5 deg
-
Gear Ratio1:1
-
TypeMinimum Plain Bore Type 4
-
Hub Diameter2-5/8 in
-
Hub Projection7/8 in
-
Diametral Pitch10
-
Number of Teeth55
-
Outside Diameter5.7 in
-
Bore Diameter7/8 to 1-9/16 in
-
Overall Length1-7/8 in
- When you think Special Gears - Think Browning
-
Alternative Part NumberNCS1055
-
UNSPSC31171707
-
Package DescriptionEACH
-
Standards/ApprovalsAGMA Standard
-
Warranty1 Year
-
Catalog
-
Warranty Information
Recently Viewed
Browning® offers a comprehensive line of off the shelf gears, including spur, miter and bevel as well as change gears. These are available in 20 deg pressure angle from 20 to 4 diametral pitch and 14.5 deg pressure angle from 48 to 3 diametral pitch. They are all designed to increase output, reduce costs and avoid the need for custom specials.
O-rings are endless, ring shaped sealing elements with a circular cross-section that are manufactured from elastomer materials or PTFE. The designation of an O-ring is derived from the dimensions of its inner diameter and cord width in millimeters, along with the name of the material and its Shore A hardness.
Proto® J406A Regular Duty C-Clamp, 3-5/8 in D Throat, 6 in Jaw Opening
Inner Rings can be integrated with shell-type or various machined needle roller bearings to provide good roller support without worrying about premature shaft wear. We heat-treat and grind our Inner Rings to tight tolerances to create hard, tough raceways for applications where it is impossible to make shaft surfaces to a specific hardness or roughness attribute. They're an economical alternative to bushings because they don't require any additional machining. Wide Inner Rings are also available to accommodate shafts that move axially or seals that are adjacent to bearings. Inner Rings come in a broad range of shaft diameters and assembly elements include small chamfers or gentle taper relief options. Inner Rings for machined-type needle roller bearings come in a variety of dimensions. Inch-type LRB series Inner Rings offer shaft diameters from 3/8 to 3-3/4 in and oil-hole versions for easier lubrication.
FYH® SA207 23FP9 SA Series Narrow Inner Ring Bearing Pillow Block Unit, 1-7/16 in Dia Bore, 1.26 in W, 25.7 kN Dynamic/15.4 kN Static Load
FYH® SA207 23FP9 SA Series Narrow Inner Ring Bearing Pillow Block Unit, 1-7/16 in Dia Bore, 1.26 in W, 25.7 kN Dynamic/15.4 kN Static Load
1/2" X 1-3/4" MD RECT DIE SPRINGS-LANSMDR500175 >
