Bearing Kits
43:1 GEAR REDUCER-LEEW5200172.00 >
25:1 RATION 140-TC GEAR REDUCER-BLDGLF2532BG>
25:1 RATIO 140-TC GEAR REDUCER-BLDGLF2526BG>
15:1 RATIO 140-TC SPEED REDUCER-BLDGLF1526BG>
900 SERIES RIGHT ANGLE WORM GEAR-BLDGLF1521AJ>
15:1 RATIO 56C GEAR REDUCER-BLDGLF1521AG>
10:1 RATIO 56-C SPEED REDUCER
F-924-25-B-7-G GEARMOTOR-BLDGF2524BG>
FLANGES-DOD6011734>
40:1 GEAR REDUCER-BRW516ULR40 >
30:1 HOLLOW SHAFT GEAR REDUCERS-BRW450UH30>
GEAR REDUCER BASE KIT-BRW450SBK >
L-PITCHX45" TIMING BELT-BRW450L100 >
L-PITCHX45" TIMING BELT-BRW450L075 >
L-PITCHX45" TIMING BELT-BRW450L050 >
H-PITCHX45" TIMING BELT-BRW450H200 >
H-PITCHX45" TIMING BELT-BRW450H150 >
H-PITCHX45" TIMING BELT-BRW450H100 >
H-PITCHX45" TIMING BELT-BRW450H075 >
20:1 GEAR REDUCER-BRW375ULR20 >
50:1 RAIDER WORM GEAR REDUCER-BRW375Q56LR50 >
60:1 RAIDER WORM GEAR REDUCER-BRW375Q180LR60 >
40:1 RAIDER WORM GEAR REDUCER-BRW375Q180LR40 >
40:1 RAIDER WORM GEAR REDUCER-BRW375Q140LR40 >
Recently Viewed
1-3/8" CAM FOLLOWER-MCGCF13/8SB >
Browning 1-3/8"-ID 2-BOLT TRB PILLOW BLOCKS BRW PBE-920 X 1-3/8
Browning® E920 series mounted tapered roller bearings feature durable 1-piece non-expansion housings with Type E mounting dimensions and limited misalignment. The E920 series contains setscrew locking collars for easy installation. It also contains a contact face riding seal in order to provide a good balance between contaminant entry, grease retention and friction. Depending on your application requirements, these bearings are available in a wide variety of bore sizes and housing configurations.
The Starrett 565 Drive Pin Punch is well proportioned, hardened, properly tempered, nicely finished, and have a knurled finger grip. Each punch has the size stamped on the head. 100mm (4") length, 5.5mm (7/32") Diameter.
HCI Preferred Supplier 32022 Rigid Adapter, 3/4 x 1/2 in Nominal, Hose Barb x MNPTF End Style, Brass
HCI Preferred Supplier 32022 Rigid Adapter, 3/4 x 1/2 in Nominal, Hose Barb x MNPTF End Style, Brass
Leviton® electrical accessories for the home include taps and adapters, nightlights and battery operated lighting. Every electrical accessory is subject to Leviton® strict in-house quality control and must meet or exceed applicable industry standards.
Drillco 690A112A 6900A Center Cutting Double End Imperial Regular Length Finishing End Mill, 3/16 in Dia Cutter, 7/16 in Length of Cut, 2 Flutes, 3/8 in Dia Shank, 3-1/8 in OAL, Uncoated
The greater red hardness of M-42 Cobalt end mills enables these tools to run about 10% faster than conventional HSS end mills. This translates to shorter machining times and permits higher utilization of available machine horsepower. Double-ended.
