Dichtomatik N70433 O-Ring, 433 Dash Number, 5.475 in ID x 6.025 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70433
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter5.475 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter6.025 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Dichtomatik N70433 O-Ring, 433 Dash Number, 5.475 in ID x 6.025 in OD, Nitrile Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
BBI 401296 Fully Threaded Cap Screw, 1/2-13, 1-1/4 in L Under Head, 316 Grade, Stainless Steel
BBI 401296 Fully Threaded Cap Screw, 1/2-13, 1-1/4 in L Under Head, 316 Grade, Stainless Steel
Browning® 1045228 VP Series Type 1 Variable Pitch Sheave, 1/2 in Finished Bore, 2-1/2 in OD, 1 Groove, 1.6 to 2.4 in Dia Pitch, 17/32 to 25/32 in W Face
The principle of a variable pitch sheave is that the threaded angular faced discs forming the V-shaped groove in which the belt rides are movable. VP sheaves consist of a male with a threaded barrel, and a female with a threaded bore. The male section with threaded barrel has flat surfaces at 180 deg increments that allow a flat surface for the setscrew to mate with. When the discs are moved toward each other, the belt rides higher in the groove and the pitch diameter of the sheave is larger which increases the driven speed. When the discs are moved away from each other, the belt rides lower and the pitch diameter is smaller decreasing the driven speed. The common term for this speed adjustment is called number of turns open from closed position.
BBI 221157 Shoulder Screw, Round Socket Head, ASTM A574 Alloy Steel, 1/2 in Dia x 5 in L Shoulder, 3/8-16
BBI 221157 Shoulder Screw, Round Socket Head, ASTM A574 Alloy Steel, 1/2 in Dia x 5 in L Shoulder, 3/8-16
72"-H X 36"-W X 18"-D BLACK STORAGE CABINET - HLW415S18ME >
BBI 451220 Partially Threaded Cap Screw, 3/4-10, 11 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451220 Partially Threaded Cap Screw, 3/4-10, 11 in L Under Head, 8 Grade, Alloy Steel, Plain
