Dichtomatik N70131 O-Ring, 131 Dash Number, 1.674 in ID x 1.88 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 131
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberN70131
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialNitrile Rubber
-
ColorBlack
-
Inside Diameter1.674 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter1.88 in
- Good chemical resistance to mineral oils and greases
- The physical and chemical resistance properties of NBR materials are determined by the acrylonitrile (ACN) content of the base polymer which can vary between 18 and 50%
- Low ACN content ensures good flexibility at low temperatures, but offers limited resistance to oils and fuels
- As the ACN content increases, the low temperature flexibility reduces and the resistance to oils and fuels improves
- Physical and chemical resistance properties of NBR materials are also affected by the cure system of the polymer
- Peroxide cured materials have improved physical properties, chemical resistance and thermal properties as compared to sulfur-donor-cured materials
- Standard grades of NBR are typically resistant to mineral oil-based lubricants and greases, many grades of hydraulic fluids, aliphatic hydrocarbons, silicone oils and greases and water to about 80 deg C
- NBR is generally not resistant to aromatic and chlorinated hydrocarbons, fuels with a high aromatic content, polar solvents, glycol based brake fluids and non-flammable hydraulic fluids (HFD)
- NBR also has low resistance to ozone, weathering and aging, but in many applications this has no negative effect
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|FDA Compliant|ISD Certified|NFPA Listed|PTDA Certified
Recently Viewed
Dichtomatik N70131 O-Ring, 131 Dash Number, 1.674 in ID x 1.88 in OD, Nitrile Rubber, 70 Shore A Durometer, Import, Custom 131
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
SYNTHETIC RUBBER TIMING BELT. COMFORMS TO RMA ENGINEERING STANDARD. TIMING BELTS ARE MEASURED BY LENGTH, TOOTH PITCH, THEN WIDTH. THE FIRST NUMBER IS THE LENGTH; THE LETTER AND SOMETIME NUMBER REFER TP THE TOOTH AND THE FINAL NUMBER IS THE WIDTH. STANDARD TIMING TOOTH PROFILE, H; FIBERGLASS TENSIILE MATERIAL; RUBBER OUTER MATERIAL
-JAS1700H150 >
NIBCO 205-015 Nipple, 1/2 in x 1-1/2 in L Thread, PVC, SCH 80/XH, Domestic
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
HCI Preferred Supplier 949164 2-Piece Ball Valve, 3/4 in Nominal, ASTM-A351 CF8M 316 Stainless Steel Body, Full Port, RPTFE Seal/Thrust Washer/Plastic Cover Softgoods
HCI Preferred Supplier 949164 2-Piece Ball Valve, 3/4 in Nominal, ASTM-A351 CF8M 316 Stainless Steel Body, Full Port, RPTFE Seal/Thrust Washer/Plastic Cover Softgoods
BBI 221187 Shoulder Screw, Round Socket Head, ASTM A574 Alloy Steel, 5/8 in Dia x 3-1/2 in L Shoulder, 1/2-13
BBI 221187 Shoulder Screw, Round Socket Head, ASTM A574 Alloy Steel, 5/8 in Dia x 3-1/2 in L Shoulder, 1/2-13
