Dichtomatik S70011 O-Ring, 011 Dash Number, 0.301 in ID x 0.441 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
-
BrandDichtomatik
-
Manufacturer Part NumberS70011
-
CountryUSA
-
Temperature Rating40 to 120 deg F
-
MaterialSilicone Rubber
-
ColorRed
-
Inside Diameter0.301 in
-
Domestic/ImportImport
-
Durometer70 Shore A
-
Outside Diameter0.441 in
- Good chemical stability in water (up to 100 deg C), aliphatic engine and transmission oils, animal and plant based oils and greases
- Not resistant to fuels, aromatic mineral oils, water vapor (short periods up to a maximum of 120 deg C are possible), silicone oils and greases, along with acids and alkaline compounds
-
UNSPSC31401503
-
Standards/ApprovalsDNV Approved|ISD Certified|NFPA Listed|PTDA Certified
-
Specification Sheet
-
Instruction/Installation Manual
-
Catalog
Recently Viewed
Dichtomatik S70011 O-Ring, 011 Dash Number, 0.301 in ID x 0.441 in OD, Silicone Rubber, 70 Shore A Durometer, Import
O-rings are closed circular rings of circular cross-section. They are made through vulcanization from form tools as a complete ring. The sealing function of the O-ring is achieved by the deformation of the cross-section when installed and compressed in its housing. The O-ring can be compressed either radially or axially in its installation housing. In operating conditions the pressure exerted by the media reinforces the sealing function, as under pressure the elastomer material functions as a non-compressible fluid.
36/50-KRAFT 50-lb Roll 36" Brown Kraft Paper
50-LB ROLL 36" BROWN KRAFT PAPER-WHY3650KRAFT >
Dodge® 117113 Stock Bore Taper Lock Bushing, 1-11/16 in Dia Bore, 4-1/4 in Dia Barrel, 2 in OAL, Sintered Steel
Dodge® Taper-Lock® bushings are flangeless for clean, compact application. They are engineered with an 8 deg taper and a flush-mounted design with no protruding parts providing secure locking and elimination of wobble.
UP TO 4 TIMES STRONGER THAN A BRASS GROMMET, MADE FROM RECYCLED POLYMERS. COMPATIBLE WITH CANVAS OR POLY TARPS
-JWH742771 >
ASP-752-SS Industry Standard Clamping Collar, 2-Piece Construction, 3/4 in ID x 1-1/2 in OD x 1/2 in W, Stainless Steel
Stainless Steel Two-Piece Clamping Collar. Design fully engages the shaft without marring. Easily installed where major disassembly would otherwise be required. Greater axial holding power than set screw or one-piece clamping collars. Effective on hard & soft shafts.
Weiler® 17263 Small Diameter Wheel Brush, 3 in Dia Brush, 3/8 in W Face, 0.016 in Dia Crimped Filament/Wire, 1/2 in Arbor Hole
Weiler® 17263 Small Diameter Wheel Brush, 3 in Dia Brush, 3/8 in W Face, 0.016 in Dia Crimped Filament/Wire, 1/2 in Arbor Hole
