BBI 451040 Fully Threaded Cap Screw, 1-1/4-12, 2-1/2 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451040 Fully Threaded Cap Screw, 1-1/4-12, 2-1/2 in L Under Head, 8 Grade, Alloy Steel, Plain
-
BrandBBI
-
UPC662403655371
-
Manufacturer Part Number451040
-
CountryUSA
-
FinishPlain
-
Tensile Strength150000 psi
-
MaterialAlloy Steel
-
Material SpecificationSAE J429
-
Thread TypeUNF
-
Measurement SystemImperial
-
TypeFully Threaded
-
Grade8
-
Hardness33 to 39 HRC
-
Head Size25/32 in H
-
Head TypeHex
-
Diameter - Thread Size1-1/4-12
-
Length Under Head2-1/2 in
-
UNSPSC31161501
-
Package Description1/CS
-
Standards/ApprovalsANSI B18.2.1-1996
Recently Viewed
BBI 451040 Fully Threaded Cap Screw, 1-1/4-12, 2-1/2 in L Under Head, 8 Grade, Alloy Steel, Plain
BBI 451040 Fully Threaded Cap Screw, 1-1/4-12, 2-1/2 in L Under Head, 8 Grade, Alloy Steel, Plain
4" X 4" PIPE FLEX COUPLING CONSTRUCTED OF ELASTOMERIC PCV THAT RESISTS CHEMICALS, SEWER GASES, AND UV RAYS. USE IN SEWER AND DWV PIPING. MAXIMUM WORKING PRESSURE 4.3" PSI. A= ID OF SIZE 1; B= ID OF SIDE 2; C= END TO END OVERALL LENGTH. 4" X 3" PIPE SIZE; 4.-JWH420808 >
45" X 8" MAGNESIUM BULL FLOAT-JWH337317 >
Sharkbite® U870W100 Tubing, 3/4 in Nominal, 0.671 in ID x 7/8 in OD x 100 ft Coil L x 0.097 in THK Wall, White, PEX, Domestic
SharkBite PEX tubing is cross-linked polyethylene tubing for a wide range of residential and commercial plumbing applications. PEX Pipe is durable, flexible and corrosion resistant. Manufactured without an oxygen barrier for potable water systems (available in white, blue, and red). A repeating SharkBite imprint patterns provides a visual aid to determine if the tube has been inserted all the way into the SharkBite Push-to-Connect Fitting. This feature only works if the tubing is cut between the SharkBite imprint patterns. In addition to Potable Water Supply SharkBite PEX meets UL Standard for Plastic Piping in Fire Systems.
Koyo IR-88 Inch Series Regular Width Inner Ring, 1/2 in ID x 3/4 in OD, 0.515 in OAW, For Use With B-126, B-128, J-126, J-128, M-1261, M-1281 Drawn Cup Needle Roller Bearing, Steel
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
BBI 486344 Lag Screw, 3/8 in, 3 in OAL, Low Carbon Steel, Zinc Blue
