POWERS 1/2" X 7" ZINC CONCRETE ANCHORS PWR 7426
The Power-Stud anchor is a fully threaded, torque-controlled, wedge expansion anchor. It is available in threaded, rod hanger and tie-wire versions suitable for applications in solid concrete and grout filled concrete masonry. The carbon steel threaded version is suitable for a variety of applications. The drill bit diameter necessary for proper installation is the same as the anchor diameter.
-
BrandDeWALT®
-
UPC075352776132
-
Manufacturer Part Number7426SD1
-
CountryUSA|Canada
-
FinishZinc Plated
-
Tensile Strength4155 lb
-
Thread Length5-1/4 in
-
MaterialCarbon Steel
-
Thread Size1/2-13
-
Thread TypeUNC
-
Maximum Work Thickness4-1/4 in
-
Minimum Embedment Depth2-1/4 in
-
TypeExpansion
-
Head TypeHex
-
SeriesSD1
-
Shear Strength4195 lb
-
Diameter1/2 in
-
Drill Size1/2 in
-
Overall Length7 in
- Consistent performance in high and low strength concrete
- Length ID code and identifying marking stamped on head of each Anchor
- Ultimate load capacity: 3800 lb tensile strength when embedded in 2500 psi, 4155 lb tensile strength when embedded in 3000 psi and 4800 lb tensile strength when embedded in 4000 psi compressive strength concrete
- Nominal drill bit size is the same as the anchor diameter
- Anchor can be installed through standard fixture holes
- Anchor design allows for follow-up expansion after setting under tensile loading ultimate pullout 5440 lb
- Normal weight concrete, structural sand-light weight concrete, concrete over steel deck and grouted concrete masonry are applicable materials
-
Alternative Part Number7426SD1-PWR
-
UNSPSC31162102
-
Package Description25/BX
-
Standards/ApprovalsICC-ES AC01, ESR-2818/2966|UL Listed|2015 IBC/IRC|ACI 318-14 Chapter 17|ACI 318-11/08 Appendix D|ACI 355.2|ASTM E488|Evaluated and Qualified by an Accredited Independent Testing Laboratory|FM Approved|ICC-ES AC193|UL EX1289
-
Catalog
-
Specification Sheet
Recently Viewed
The Power-Stud anchor is a fully threaded, torque-controlled, wedge expansion anchor. It is available in threaded, rod hanger and tie-wire versions suitable for applications in solid concrete and grout filled concrete masonry. The carbon steel threaded version is suitable for a variety of applications. The drill bit diameter necessary for proper installation is the same as the anchor diameter.
10" 4-GA BLACK TOP POST CABLE-PRI00784 >
Series 7000 is very robust and ideal for the most demanding applications. The reel's base and guide arm are formed from high grade steel engineered with structural forms and gussets to yield the greatest amount of strength. The standard low pressure hose is for air or water service only. The basic reel without hose can be used for air, water or oil. Guide arm adjusts to three positions.
5" SUCTION HOSE CLAMP - DXNSDBC5 >
Coilhose® CMF38 Conical Muffler, 3/8 in MPT Port, 11/16 in Hex, 1-9/16 in OAL
Coilhose® CMF38 Conical Muffler, 3/8 in MPT Port, 11/16 in Hex, 1-9/16 in OAL
Steel shim is made from a full hard, cold rolled, low carbon 1008-1010 steel. Precision Brand® is the only manufacturer to offer Branded® shim. It has everything the user needs to know clearly marked right on the shim: material type, material thickness and lot # for full traceability. Used in applications where hardness, flatness and accuracy are required. Material can be punched or sheared with minimum burring and distortion. Precision Brand® shim stock is widely used in the following applications: tool and die set up, alignment, new machine assembly, machine repair and maintenance; mounting of motors, pumps and other machines, short run and prototype work, along with a variety of other industrial uses. It is especially useful for pilot production runs where material accuracy and economy are important. All Precision Brand® shim products are manufactured under rigorous quality control standards to assure high accuracy and tight tolerances.
