Drillco 72A140C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 5/8 in Dia Cutter, 1-1/4 in Length of Cut, 2 Flutes, 5/8 in Dia Shank, 3-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
-
BrandDrillco
-
UPC045997390215
-
Manufacturer Part Number72A140C
-
CountryUSA|Canada
-
FinishUncoated
-
MaterialSolid Carbide
-
Flute TypeSpiral
-
TypeCenter Cutting Imperial Regular Length Single End
-
Helix Angle30 deg
-
Series7200
-
Cutter Diameter5/8 in
-
Shank Diameter5/8 in
-
Number of Flutes2
-
Cutting DirectionRight Hand
-
Shank TypeRound
-
Length of Cut1-1/4 in
-
Overall Length3-1/2 in
- Solid carbide construction for extreme rigidity and strength
- Center cutting tip for plunging, pocketing and holemaking
- Solid carbide can be ran at 3x the speed and feed of HSS
- 2 flutes provide more efficient chip removal
- Bright finish for added lubricity
-
UNSPSC27112803
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product can expose you to chemicals including Cobalt, which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
-
SDS
-
Catalog
Recently Viewed
Drillco 72A140C 7200 Center Cutting Imperial Regular Length Single End Finishing End Mill, 5/8 in Dia Cutter, 1-1/4 in Length of Cut, 2 Flutes, 5/8 in Dia Shank, 3-1/2 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life.
CRC® 03041 Dry Film Extremely Flammable Multi-Purpose Silicone Lubricant, 5 gal Pail, Liquid Form, Clear/Water White, -40 to 400 deg F
Multi-purpose silicone spray for food processing and handling applications. Forms a colorless, odorless, non-staining film. Eliminates binding and sticking in most metal to non-metal applications. Meets FDA Regulation CFR 21-178.3570. NSF H1 Registered.
USED FOR NEW MACHINERY, GENERAL MAINTENANCE AND SHOP REPAIRS. IT IS A NECESSITY IN ALL APPLICATIONS WHERE ROTATING POWER DEVICES ARE USED. MOST TOLERANCES ON DIMENSIONS ARE OVERSIZED TO ASSURE TIGHT FITS IN KEYWAYS FOR POSITIVE, ZERO BACKLASH POWER TRANSMISSION
-PRC15200 >
JASON 3L620 FRACTIONAL HORSEPOWER V-BELT, 3/8" TOP WIDTH, 7/32" THICK, 62" LENGTH
OIL & HEAT RESISTANT-DURABILITY IN TOUGH ENVIRONMENTS. FLEXIBLE IDEAL FOR USE WITH BACKSIDE IDLERS, STATIC DISSIPATING, MADE OF NATURAL RUBBER/SBR CORD OF POLYESTER AND COVERED WITH COTTON/POLYESTER BLEND
-JAS3L620 >
Remke Tuff-Seal™ 7303-014R Closed Mesh Insulated Single Weave Wide Range Strain Relief Grip With Galvanized Steel Mesh, 1.2 to 1.5 in Cable, For Use With 1-1/2 in NPT Connector, Aluminum
Tuff-Seal™ Wire Mesh Cable Grips distribute stress over a large area to prevent damage to wire, cable and flexible conduit. They are built to perform their task over an extended period of time without loosening their hold. All Remke wire mesh grips are available in a wide selection of cable ranges and eye styles where applicable and can be used in conjunction with any RSR cord connector.
Sealmaster® gold mounted ball bearings feature a wide outer race insert bearing with land riding metallic retainer. The black oxide treated bearing steel insert features an exclusive lock pin and dimple system providing a direct path for lubrication into the bearing, and prevents outer ring rotation within the housing. Shaft lock is achieved by either setscrew or Skwezloc® concentric locking collar. The felt seal with flinger provide a good balance between contaminant entry, GoldPlex® HP grease loss and friction. Depending on your preference, these bearings are available in both inch and metric shaft sizes with a wide variety of cast iron, stamped steel or rubber mount housings, sealing, and lubrication options or industry specific solutions.
