Drillco 76A128C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 7/16 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 7/16 in Dia Shank, 2-3/4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
-
BrandDrillco
-
UPC045997391809
-
Manufacturer Part Number76A128C
-
CountryUSA|Canada
-
FinishUncoated
-
MaterialSolid Carbide
-
TypeCenter Cutting Imperial Regular Length Single End
-
Series7600
-
Cutter Diameter7/16 in
-
Shank Diameter7/16 in
-
Number of Flutes2
-
Shank TypeRound
-
Length of Cut1 in
-
Overall Length2-3/4 in
- Solid carbide construction for extreme rigidity and strength
- Ball nose for profiling and grooving with radii, and contouring
- 2 flutes provide more efficient chip removal
- Bright finish for added lubricity
-
UNSPSC27112803
-
Package Description1/PK
-
Standards/ApprovalsPROP65: This product can expose you to chemicals including Cobalt, which is [are] known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.
-
SDS
-
Catalog
Recently Viewed
Drillco 76A128C 7600 Center Cutting Imperial Regular Length Single End Ball Nose End Mill, 7/16 in Dia Cutter, 1 in Length of Cut, 2 Flutes, 7/16 in Dia Shank, 2-3/4 in OAL, Uncoated
Solid carbide end mills run at extremely impressive feed and speed rates. In some cases, they can be run at 3x the rates of HSS end mills. Using solid carbide end mills results in better surface finish on the workpiece and extended tool life. Ball nose.
Dodge® 117705 Stock Bore Taper Lock Bushing, 4-15/16 in Dia Bore, 6.38 in Dia Barrel, 4-1/2 in OAL, Ductile Iron
Dodge® Taper-Lock® bushings are flangeless for clean, compact application. They are engineered with an 8 deg taper and a flush-mounted design with no protruding parts providing secure locking and elimination of wobble.
The single-row angular contact ball bearing was designed to support radial, axial or composite loads, however, the axial load must be in one direction. The high thrust capacity is achieved by a higher shoulder on one side of the outer ring. A matching high shoulder is often on the opposite side of the inner ring as well. The direction of the load through the balls forms the contact angle. The thrust capacity increases with the contact angle. This ball bearing has a 40 deg contact angle. This bearing has a stamped steel cage and is not available with seals or shields. These bearings are non-separable. These bearings have normal tolerances and are not suitable for mounting adjacent to each other to achieve a preload.
10" DECK BRUSH WITH 3" PALMYRA TRIM - MAG1103 >
MINI-PULLER, 1/2" TON 0R 1,100LB LOAD CAPACITY, VERY COMPACT & LIGHTWEIGHT, LOW PULLING FORCE REQUIRED FOR OPERATION, 5FT LIFT-HRHLX0055 >
Where it becomes impractical to meet the shaft raceway design requirements (hardness, case depth, surface finish, etc.) outlined in the engineering section, standard inner rings for drawn cup bearings are available. Inner rings for drawn cup bearings are designed to be a loose transition fit on the shaft and should be clamped against a shoulder. If a tight transition fit must be used to keep the inner ring from rotating relative to the shaft, the inner ring OD as mounted, must not exceed the raceway diameters required by the drawn cup bearing for the particular application.
